The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-16-2014, 11:40 AM   #1
FarmerDale
Registered User
 
Join Date: Jan 2013
Location: Easton,mn
Posts: 22
Gauge cluster questions

I have my gauge cluster('87 with clock) apart so I can brighten it up with a good cleaning and a little chrome paint for the backlight. 2 things grabbed my attention:
1. A few of the rivets holding the gauges to the dial face have some surface rust. What is my best approach to eliminate this? Was thinking a dab of paint over sanded metal (awful tight quarters with the dial face) or making it bright then wax the whole dial.
2. The printed circuit is not uniformly attached to the cluster. Do I completely remove it before painting the cluster or leave it and tack the loose areas down later? And with what adhesive?
Thanks for your help - Dale
FarmerDale is offline   Reply With Quote
Old 09-16-2014, 01:20 PM   #2
gmachinz
Account Suspended
 
Join Date: Jun 2011
Location: Des Moines, IA.
Posts: 4,143
Re: Gauge cluster questions

From my experience, don't use a chrome paint. Instead, go with a plastic primer adhesion promoter then high gloss white and LED 194 bulbs-that will be killer bright! As for the circuit board, I would carefully remove it before cleaning. Now for the surface rust on the rivets, simply dab it with a black Sharpie or dab it with Testors satin black model paint using a toothpick. Once its all assembled and installed, it isn't noticeable.
gmachinz is offline   Reply With Quote
Old 09-16-2014, 01:38 PM   #3
FarmerDale
Registered User
 
Join Date: Jan 2013
Location: Easton,mn
Posts: 22
Re: Gauge cluster questions

Great suggestions GMachinz. I was going to do the LEDs upgrade. My aging eyes will enjoy it. Rust camouflage sounds easy enough also. Do I really the circuit with silicon, rubber cement or is there a better adhesive?
FarmerDale is offline   Reply With Quote
Old 09-16-2014, 01:57 PM   #4
gmachinz
Account Suspended
 
Join Date: Jun 2011
Location: Des Moines, IA.
Posts: 4,143
Re: Gauge cluster questions

I wouldn't suggest NOT using an adhesive on the printed circuit board-just carefully pop the tabs out. Worst case, a new circuit from LMC isn't much...unless you have an electronic speedo-not sure if anybody offers that style or not-it has a plug-in receiver port instead of tension tangs.
gmachinz is offline   Reply With Quote
Old 09-16-2014, 02:17 PM   #5
johnwaynejeep
Registered User
 
Join Date: Jul 2014
Location: Pacific Grove, CA
Posts: 105
Re: Gauge cluster questions

the printed circuit should be held in place by the bulbs and the gauge tabs that feed through the back. Once everything is in place it holds real nice. I wouldn't put any adhesive on it becuase it will be much harder to replace in the future, but this is all personal preference for me. If you decide on an adhesive, make sure to use something that is non-conductive so the adhesive doesn't short out any of the runs and cause a fire or blown fuses. Any good electrical outlet can provide you with a non-conductive adhesive.

For the gauge rust. Be careful with the paint on the gauges. I tried to use window cleaner to clean off some of the dust from the gauges before reassembly and the white lettering will come off just with light rubbing, let alone any kind of cleanser. I think the black sharpie is a great idea for this.

While you have it out and apart. Look for signs of corrosion on the printed circuit board. On mine, all the runs looked green as opposed to the silver or copper color they have when they are new. If you see signs of greening then your board is starting to corrode and eventually some of the gauges or lights will quit on you.

this would also be a good time to remove all the gauge tabs and lights and clean them up. I used a light grade wire brush attached to my drill and very lightly sanded all the contacts until they were shiney again. You don't need any tools to remove the gauge tabs, they can be removed by pressing on them in the right spot and angling them out.
__________________
Robert
1975 C10 - Huckleberry
2007 Jeep JK - John Wayne Jeep
Smittybilt front/rear bumper, 10K winch
Pacific Grove, CA

Last edited by johnwaynejeep; 09-16-2014 at 02:23 PM. Reason: Added reference to electrical safety
johnwaynejeep is offline   Reply With Quote
Old 09-16-2014, 02:35 PM   #6
gmachinz
Account Suspended
 
Join Date: Jun 2011
Location: Des Moines, IA.
Posts: 4,143
Re: Gauge cluster questions

I'd like to add that with it out, slightly bend out each of the cluster plug tangs for in the dash harness-this helps ensure a good contact again.
gmachinz is offline   Reply With Quote
Old 09-16-2014, 03:01 PM   #7
motornut
78K & 79C Jimmys
 
motornut's Avatar
 
Join Date: Nov 2009
Location: Ottawa Ont CANADA
Posts: 7,901
Re: Gauge cluster questions

I removed everything ,washed housing and used gloss white paint worked great
light sanding on the paths,then used crazy glue to reglue the copper paths to the mylar plastic,no prob
I added red LEDs as well
don't glue the gauge pastic to the houseing tho
Attached Images
     
__________________
John
1978 GMCJimmy4X4-350/203
1979 GMCJimmy4X2-305/350
motornut is offline   Reply With Quote
Old 09-16-2014, 03:08 PM   #8
motornut
78K & 79C Jimmys
 
motornut's Avatar
 
Join Date: Nov 2009
Location: Ottawa Ont CANADA
Posts: 7,901
Re: Gauge cluster questions

here are some path issues i fixed with crazy glue,and cleaned up/rebent out the pug
Attached Images
     
__________________
John
1978 GMCJimmy4X4-350/203
1979 GMCJimmy4X2-305/350
motornut is offline   Reply With Quote
Old 09-16-2014, 08:11 PM   #9
gmachinz
Account Suspended
 
Join Date: Jun 2011
Location: Des Moines, IA.
Posts: 4,143
Re: Gauge cluster questions

Looks good! The LEDs and bright white paint is a killer look! The clusters never looked this good even when brand new!
gmachinz is offline   Reply With Quote
Old 09-17-2014, 11:18 AM   #10
motornut
78K & 79C Jimmys
 
motornut's Avatar
 
Join Date: Nov 2009
Location: Ottawa Ont CANADA
Posts: 7,901
Re: Gauge cluster questions

Quote:
Originally Posted by gmachinz View Post
Looks good! The LEDs and bright white paint is a killer look! The clusters never looked this good even when brand new!
I left the stock white bulbs,working as intended,the red are LEDs on with the key
My friend with a 72 Skylark wants me to do his,white only tho
__________________
John
1978 GMCJimmy4X4-350/203
1979 GMCJimmy4X2-305/350
motornut is offline   Reply With Quote
Old 09-17-2014, 12:08 PM   #11
FarmerDale
Registered User
 
Join Date: Jan 2013
Location: Easton,mn
Posts: 22
Re: Gauge cluster questions

I will go over the circuit more closely but I don't see any corrosion. A black paint pen was used to cover the rivets, so should have a little more protection than a Sharpie. Thanks for the advice on removing the circuit. Now I can see that it was just a grip fit deal, and I will keep that feature!
FarmerDale is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:12 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com