front roll pan ? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

stepside71 · 01-25-2004, 05:16 PM

I've seen new aftermarket ones listed @ $ 200. Is that the going rate ? I admit that I am cheap and do not wish to pay that much. Here's the deal, I am building my truck from the ground up. It will be a daily driver not a show truck. Therefore I am not willing to spend big dollars on any 1 item. Can these be self fabricated easily?

cdowns · 01-25-2004, 05:27 PM

anything can be fabricated depends on the skill level of the person trying to do it
the easy way to find out is get youself a piece of 18 or 20 gauge sheetmetal and try it

Longhorn Man · 01-25-2004, 06:14 PM

Look into your local laws before doing this. Federal law mandates a front bumper (but some states do not enforce it) and to do a front roll pan you'll have to chop off about 4 to 6 inches of frame rail (where the bumper bolts up to) so it is not easy to go back once you do it.

MrShelley · 01-25-2004, 07:42 PM

I don't think you need to chop that much frame to fit the pan. On the Mar-K website it says you have to remove 2" to fit their pan. I chopped mine back flush with the radiator support mounts just to make sure it was back far enough.

Check here for a cheaper price on the pan itself. LINK

Longhorn Man · 01-26-2004, 01:39 AM

Even so, it is a frame mod that is harder to reverse than a simple nut and bolt procedure.

MrShelley · 01-26-2004, 01:29 PM

I agree, it isn't a decision to take lightly. It's not like you can just "bolt it back on". But it does look good (in my opinion), especially on 67-68's.

01-25-2004, 05:16 PM	#1
stepside71 Project Money Pit Join Date: Jan 2004 Location: Pensacola Florida Posts: 90	front roll pan ? I've seen new aftermarket ones listed @ $ 200. Is that the going rate ? I admit that I am cheap and do not wish to pay that much. Here's the deal, I am building my truck from the ground up. It will be a daily driver not a show truck. Therefore I am not willing to spend big dollars on any 1 item. Can these be self fabricated easily?

01-25-2004, 05:27 PM	#2
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	anything can be fabricated depends on the skill level of the person trying to do it the easy way to find out is get youself a piece of 18 or 20 gauge sheetmetal and try it __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-25-2004, 06:14 PM	#3
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Look into your local laws before doing this. Federal law mandates a front bumper (but some states do not enforce it) and to do a front roll pan you'll have to chop off about 4 to 6 inches of frame rail (where the bumper bolts up to) so it is not easy to go back once you do it.

01-25-2004, 07:42 PM	#4
MrShelley Too Many Clubs Club Join Date: Jul 2003 Location: Kilgore, Texas Posts: 443	I don't think you need to chop that much frame to fit the pan. On the Mar-K website it says you have to remove 2" to fit their pan. I chopped mine back flush with the radiator support mounts just to make sure it was back far enough. Check here for a cheaper price on the pan itself. LINK

01-26-2004, 01:39 AM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Even so, it is a frame mod that is harder to reverse than a simple nut and bolt procedure.

01-26-2004, 01:29 PM	#6
MrShelley Too Many Clubs Club Join Date: Jul 2003 Location: Kilgore, Texas Posts: 443	I agree, it isn't a decision to take lightly. It's not like you can just "bolt it back on". But it does look good (in my opinion), especially on 67-68's.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.