Project: Shiro

[GAc10boy]

Coming together so well! Love the 68 frontend.

[C10_ustacould]

Been a couple of weeks since I have posted any updates, not much going on. I am in wallet recovery mode from the cab repairs and will be for a bit so I have been working on things that done need money thrown at it. Cab/bed placement has been the focus for the last 2 weeks and I have been getting my butt kicked by the gap between the cab and the bed. The passenger side is .875" and the driver side is 1.125"... a .250" cause serious frustration.



Going to order another set of tubs from the folks at Nsane Hot Rodz tomorrow so that I can widen these by 1.5" make a little more wiggle room for the wheels and tires. And some room for future growth...

[sduckworth13]

Vic1947 was having the same issue with his bed before he put the truck away to work on his 1957 Ford. He thinks the frame is bent, not 100% sure till he pulls it back out and sends it to the frame shop to revisit the issue. He moved the core support, cab and bed around to compensate for the gap and the holes for the cab and core supports weren't close to lining up.

[C10_ustacould]

Originally Posted by sduckworth13

Vic1947 was having the same issue with his bed before he put the truck away to work on his 1957 Ford. He thinks the frame is bent, not 100% sure till he pulls it back out and sends it to the frame shop to revisit the issue. He moved the core support, cab and bed around to compensate for the gap and the holes for the cab and core supports weren't close to lining up.

Well,I measured the frame when I put it back together and it was dead nuts on. I think I just have a lot of new sheet metal and it's going to take some work to get it sorted. I don't have experience with body alignment and such so it going to be a lesson for sure.

[aggie91]

I know that you have a steel floor bed, but check the bed to make sure it is square when bolted together. If its not, that just adds to the frustration....

[C10_ustacould]

Shiro will be parted out, be on the lookout in the classifieds. I will be doing the partout in a specific order; wheels, engine/trans, chassis, and finally the body.

[KMC3420]

Originally Posted by Bucks68

Shiro will be parted out, be on the lookout in the classifieds. I will be doing the partout in a specific order; wheels, engine/trans, chassis, and finally the body.

What, no way! I was hoping for a different update, GLWS.

[Ol Blue K20]

Originally Posted by bucks68

shiro will be parted out, be on the lookout in the classifieds. I will be doing the partout in a specific order; wheels, engine/trans, chassis, and finally the body.

huh!!!!!!!!why!!!!!!

[smbrouss70]

That TADD kicked in didn't it? What'cha looking for? A Blazer?

[C10_ustacould]

Originally Posted by KMC3420

What, no way! I was hoping for a different update, GLWS.

Originally Posted by Ol Blue K20

huh!!!!!!!!why!!!!!!

Originally Posted by smbrouss70

That TADD kicked in didn't it? What'cha looking for? A Blazer?

The plain truth is that I have built this truck beyond my means and it has to go. At this point there is no plan to replace the truck.

[nlped]

Ahhhh Man! I hate hear this...seems like you were finally getting close...

I'll be watching the classifieds for sure though

[Ol Blue K20]

I hate to to hear this too but we all have to do what is we have to sometimes. I wish you the best of luck.

[shawno72]

Whoa. Best of luck to you.

[Coursey]

Glws!

[lolife99]

I hate to hear this.
But the plain truth is,... it would take another big wad of cash to finish this truck.
Alot of people don't see that,... but I do.
Quality paint and interior is just two of the big ticket items.
(Have you priced paint materials lately? CRAZY!)

Good luck with the part out.

[knomadd]

Well that sucks. Good luck though.

[kitsbeach]

Originally Posted by Bucks68

Shiro will be parted out, be on the lookout in the classifieds. I will be doing the partout in a specific order; wheels, engine/trans, chassis, and finally the body.

Oh man..!! I hate to hear this too I was enjoying following along and you almost had me talked into the Ridetech HQ's.

I have only a rough plan of what my eventual costs will be with LS swap etc but thank you for the reminder for me to plan ahead and not go to deep into it.

The patina guys have it figured out.!!

[Hart_Rod]

Originally Posted by lolife99

I hate to hear this.
But the plain truth is,... it would take another big wad of cash to finish this truck.
Alot of people don't see that,... but I do.
Quality paint and interior is just two of the big ticket items.
(Have you priced paint materials lately? CRAZY!)

Good luck with the part out.

+1, people don't understand that until they do it. It sucks, but I know Buck did some serious soul searching before making this decision.

[cooperhw]

Aw Man. That truly does suck.

I only read the first page of the build (honeymoon) and then jumped to the last page (divorce) hoping to see a bad*ss truck finished.

Don't feel bad, it happens to the best of us all at one time or another. Unfortunately those (hard) lessons are what really teach us. You will live to fight another day and do another hot rod at some point in time, only then you will be sooooo much wiser and make more solid choices.
Keep coming back to the site. Your wisdom "could" be so valuable to someone else jumping in head first.

[kitsbeach]

He will have another truck a month from now...

[Coursey]

Originally Posted by Hart_Rod

+1, people don't understand that until they do it. It sucks, but I know Buck did some serious soul searching before making this decision.

Tough decision I am sure!

[mcbassin]

Sorry to read you are parting it out. I was looking forward to an update.....Good luck with the sale.

[sduckworth13]

Good luck with your sale Buck. Lots of Nice parts

[Malamute]

Man, I'm really sorry to hear this Ernie. I'm sure that was a grueling decision. BOL!

[slowcpe]

Stinks to hear, but understand. I'm spending way more, and taking way longer, than I ever expected when I purchased my first truck.