Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
03-09-2016, 11:35 PM | #1 |
Registered User
Join Date: Jan 2016
Location: Indianapolis, IN
Posts: 12
|
70 Fleetside Bed Questions
What is the process to replace the bed rear cross sill? Also how difficult is the bed removal to replace the bolts and mounting pads.... thanks
|
03-10-2016, 01:26 AM | #2 |
Registered User
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
|
Re: 70 Fleetside Bed Questions
grind the welds off, replace sill and reweld it, may be hard to get some of the bolts off, spray with rust penetrant,I will spray all of the bolts, wait a day spray again and maybe one more time before I try and get the nuts off the bolts,I have had good success doing this...
|
03-11-2016, 08:06 PM | #3 |
Registered User
Join Date: Jan 2016
Location: Indianapolis, IN
Posts: 12
|
Re: 70 Fleetside Bed Questions
Thanks for that info, however, It appears that I will have to remove the bed as the the rear sill mounts on top of the frame? Wont drop down..... Oh and the bolts are gonna have to be cut off. The nuts are partially rusted away
|
03-11-2016, 11:16 PM | #4 |
Born Psycho
Join Date: Feb 2001
Location: brentwood,cal,usa
Posts: 4,936
|
Re: 70 Fleetside Bed Questions
i used a 4x4 with an eye bolt in the center of the wood across the inside of the bed and a cherry picker, it might take a couple of tries to get it centered in the bed then lift it up and roll the truck out, piece of cake!!!!! i swapped 3 beds one morning that way and still made it to a BBQ by lunch.
__________________
jerry moss 72 cheyenne super K20- tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,tow hooks,bumper guards,toolbox,aux. fuel tank,posi front and rear,plus other goodies!!! SOLD 69 suburban K20-tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,4 inch all spring lift,4 speed, 14 bolt full floater, dana 44 HD,warn winch,posi front and rear,tow hooks,plus other goodies. 73/80 chevy/gmc K20 SB400,turbo 400,205,tilt,a-c,gas hog. 77 K/5 cheyenne blazer-daily driver/beater. SON HAS IT NOW BRENTWOOD,CALIFORNIA |
03-25-2016, 04:25 PM | #5 |
Registered User
Join Date: Jan 2016
Location: Indianapolis, IN
Posts: 12
|
Re: 70 Fleetside Bed Questions
Well, got the bed off. Wasn't too bad removing it by myself. Thanks for all the input and info! I do have a question about what I found on the front bulkhead on the bed . There are some numbers and a couple letters on it, T T 376 25/04 (see pic). Should I leave that or is it nothing? Also, there are numbers on the top of the firewall .....Does anyone know where i could get matching yellow spray paint in a can for some touch up or best to get mixed and spray with gun?
|
03-25-2016, 06:07 PM | #6 |
Registered User
Join Date: Oct 2009
Location: Tampa Bay
Posts: 1,549
|
Re: 70 Fleetside Bed Questions
Denny, this thread will give you some insight on those markings.
http://67-72chevytrucks.com/vboard/s...light=graffiti The 376 is most likely the job number. No idea on the 25/04 or the T T. That's very interesting to see, especially from a Oshawa truck. What does the firewall say? Can't read it in the pic.
__________________
CHEVY/GMC VIN DECODERS |
03-25-2016, 07:41 PM | #7 |
Florida Edition
Join Date: Oct 2010
Location: Fruitland Park, FL
Posts: 4,028
|
Re: 70 Fleetside Bed Questions
Bruceman's on the case, your in the right place
__________________
70 GMC Short Stepside "Rose"-An American Beauty: Factory 402/TH400, AM/FM, AC, Tilt, Tach, Buckets, Posi, PS, PB, 3-5 Drop, Complete Resto-Rod 67 C-20 Slant Back Wrecker "Mad Max" 67 C-10 Ratrod "Step-N-Wolf" 71 Serro Scotty Sportsman camper "Scotty" 97 LT1 Z28 "The Hornet" Link to more pics of "Rose" http://67-72chevytrucks.com/vboard/a...p?albumid=1684 Check out my "Cheap Tricks" thread and add to it if you can, lots of good info there. http://67-72chevytrucks.com/vboard/s...d.php?t=489394 |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|