can u use a low hump cab as a 4x4? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**diggy** · 03-15-2004, 09:30 PM

I am rebuilding a 69 swb 4x4. The cab i have is the old 2x4 type with a low hump. Can i use this as it sits (knowing i have to cut a hole for tx case shifter) or do i have to cut out the entire hump and use a 4x4 hump in it's place.

any help woild be appeciated.

thanks

Blue_71 · 03-15-2004, 09:33 PM

i think you can get by with it-- but you have to use a 2" body lift

JimKshortstep4x4 · 03-15-2004, 09:34 PM

The low hump cab will definitely work on your 4x4.

I would suggest cutting out the low hump and installing the high hump, though.

Changing the transmission/transfer case is a lot easier with a removable hump.

Jim

**CPNE** · 03-15-2004, 09:35 PM

It is very simple to cut the floor out and bolt in a hump. A hump should not be too hard to find. You won't have clearance without doing this.

redneck_motorsports · 03-15-2004, 09:49 PM

Let me tell you from expierance. If you plan to have any body lift at all, go with the low hump. If you have an automatic tranny go with low hump. This is alot easier than extending your shifters. My host is down right now but when it comes back up I will post pictures of what Im talking about.

Catfish

JimKshortstep4x4 · 03-15-2004, 09:53 PM

Jeff,

We have a 72 4x4 with the low hump cab, no lift, stock cab mounts and it clears. We bought it that way, but we are going to cut out the hump asap. Installing or removing the transmission/transfer case in a low hump cab is a dangereous nightmare.

Jim

**CPNE** · 03-15-2004, 09:56 PM

Quote:

Originally posted by JimKshortstep4x4
Jeff,

We have a 72 4x4 with the low hump cab, no lift, stock cab mounts and it clears. We bought it that way, but we are going to cut out the hump asap. Installing or removing the transmission/transfer case in a low hump cab is a dangereous nightmare.

Jim

Agreed. I guess by clearance I meant to include the qualifier "enough"

**diggy** · 03-15-2004, 09:57 PM

i have a 2.5 inch susp. lift right now with a possible 4- 6 inch lift a few years down the road (when i move into a house with a taller garage door...lol)

1 ] will this make a difference?

2 ] if i did a floor shifter (for my 700r4) would there be any complications with that and the tx case shifter on the floor side by side?

(i am not sure i will do a floor shifter, i just am curious)

thanks again to all

redneck_motorsports · 03-15-2004, 10:02 PM

This is in my 67. After cutting the hump down as low as possible I only have 4" of the t-case shifter sticking out. There is also a long and a short t-case shifter from the factory depending on the tranny. I have the long one.

Mudder · 03-16-2004, 04:36 AM

I have a low hump, a body lift and the shifter is lengthened about 3 inches.

ts71281 · 03-16-2004, 12:31 PM

I don't mean to hi-jack this thread..........However, this raises an interesting question. I have a low hump cab and plan on putting a muncie 4spd in my truck soon, can I get away with just cutting a hole for the shifter or does the floor have to be clearanced for the top of the trans?

**JIMs70GMC** · 03-16-2004, 05:07 PM

I just cut the hump out of a 2wd cab that I put on my 4wd chassis w/ sm465 and np205. If you have the high hump it's real easy to drill and bolt on after cutting the hole. I'll take some pics when it quits raining.

**JIMs70GMC** · 03-16-2004, 08:19 PM

1

**JIMs70GMC** · 03-16-2004, 08:19 PM

2
I took the tc shifter off when I swapped cabs, but you can see where it goes.

**diggy** · 03-18-2004, 01:49 PM

ttt

03-15-2004, 09:30 PM	#1
diggy Registered User Join Date: Aug 2003 Location: Las Vegas Posts: 137	can u use a low hump cab as a 4x4? I am rebuilding a 69 swb 4x4. The cab i have is the old 2x4 type with a low hump. Can i use this as it sits (knowing i have to cut a hole for tx case shifter) or do i have to cut out the entire hump and use a 4x4 hump in it's place. any help woild be appeciated. thanks

03-15-2004, 09:35 PM	#4
CPNE Resident Curmudgeon Join Date: Dec 1999 Location: NH Posts: 6,664	It is very simple to cut the floor out and bolt in a hump. A hump should not be too hard to find. You won't have clearance without doing this. __________________ Currently on or near the homestead: 67 Chevy SWB 2WD stepside 350/3 on tree (Pat's) 67 GMC SWB 2WD Fleet 402/auto (Brian's under construction) 67 Chevy 3/4 ton 2WD 402/auto (Business Hauler) 67 Chevy 1 ton dually 2WD 396/4 speed (Former business hauler, Needs TLC) 68 Chevy 1/2 ton Suburban 2WD 250 six/3 on tree (Brian's Needs TLC) 70 Chevy 3/4 ton 4WD 350/4 speed (Pat's - Disguised as a 68 GMC) 71 Chevy SWB stepside (Crushed by tree - parts donor) 72 Chevy 3/4 ton 4WD (Parts donor) 72 Chevy 3/4 ton 4WD Suburban (Parts Donor) 72 GMC 3/4 ton 4WD 292 six/4 speed (Mine - Disguised as a 67 GMC) 81 GMC 4WD Dually Dump Body 350/4 speed (Business Hauler) 82 Camaro Z/28 355/Super T-10 (Pat's toy) 93 Caprice 9C1 (Brian's Cop Car) 02 Toyota Camry (Reliable but a souless steel and plastic hulk) 2011 2SS RS Camaro M6 Factory Hurst Shifter Maybe I need to sell some of this crap Yet another Bozo with a sawz-all

03-16-2004, 05:07 PM	#12
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	I just cut the hump out of a 2wd cab that I put on my 4wd chassis w/ sm465 and np205. If you have the high hump it's real easy to drill and bolt on after cutting the hole. I'll take some pics when it quits raining. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-16-2004, 08:19 PM	#13
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	hump pics 1 Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-16-2004, 08:19 PM	#14
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	2 2 I took the tc shifter off when I swapped cabs, but you can see where it goes. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-15-2004, 09:34 PM	#3
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	The low hump cab will definitely work on your 4x4. I would suggest cutting out the low hump and installing the high hump, though. Changing the transmission/transfer case is a lot easier with a removable hump. Jim

03-15-2004, 09:49 PM	#5
redneck_motorsports Registered User Join Date: Dec 2003 Location: Pampa Texas Posts: 36	Let me tell you from expierance. If you plan to have any body lift at all, go with the low hump. If you have an automatic tranny go with low hump. This is alot easier than extending your shifters. My host is down right now but when it comes back up I will post pictures of what Im talking about. Catfish

03-15-2004, 09:53 PM	#6
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Jeff, We have a 72 4x4 with the low hump cab, no lift, stock cab mounts and it clears. We bought it that way, but we are going to cut out the hump asap. Installing or removing the transmission/transfer case in a low hump cab is a dangereous nightmare. Jim

03-15-2004, 09:57 PM	#8
diggy Registered User Join Date: Aug 2003 Location: Las Vegas Posts: 137	i have a 2.5 inch susp. lift right now with a possible 4- 6 inch lift a few years down the road (when i move into a house with a taller garage door...lol) 1 ] will this make a difference? 2 ] if i did a floor shifter (for my 700r4) would there be any complications with that and the tx case shifter on the floor side by side? (i am not sure i will do a floor shifter, i just am curious) thanks again to all

03-15-2004, 10:02 PM	#9
redneck_motorsports Registered User Join Date: Dec 2003 Location: Pampa Texas Posts: 36	This is in my 67. After cutting the hump down as low as possible I only have 4" of the t-case shifter sticking out. There is also a long and a short t-case shifter from the factory depending on the tranny. I have the long one.

03-16-2004, 04:36 AM	#10
Mudder Registered User Join Date: Feb 2001 Location: East Central, MO Posts: 11,336	I have a low hump, a body lift and the shifter is lengthened about 3 inches.

03-16-2004, 12:31 PM	#11
ts71281 Registered User Join Date: Apr 2003 Location: Maple Grove, MN Posts: 497	I don't mean to hi-jack this thread..........However, this raises an interesting question. I have a low hump cab and plan on putting a muncie 4spd in my truck soon, can I get away with just cutting a hole for the shifter or does the floor have to be clearanced for the top of the trans?

03-18-2004, 01:49 PM	#15
diggy Registered User Join Date: Aug 2003 Location: Las Vegas Posts: 137	ttt

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.