![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Sep 2009
Location: Visalia, CA
Posts: 247
|
Add EGR Wiring to Aftermarket Harness
I have an aftermarket tbi harness that does not have the egr wiring. Does anyone know how I could add this wiring? Do I just take the red and white wires from the egr connector and connect them to the proper pins on the ecm?
__________________
Coop34 70 Chevy C10 5.7L TBI/700R4 |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Oct 2008
Location: Marianna Arkansas
Posts: 7,270
|
Re: Add EGR Wiring to Aftermarket Harness
That is the EGR solenoid it is connected to the actual valve. The most times The EGR is programmed out of the E-PROM chip in the ECM is aftermarket and performance cases. Know all of this is from memory and that is going back a LONG way to come up with that info.But that isn't as impressive as this recalling the service number for the truck TBI ECM, watch this. 1227747 Boom.[I built a lot of trucks back then]
So saying that to say this I don't know if trying to put the egr solenoid into the system if the computer would even recognize what it is and what it is for |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jul 2013
Location: Winnsboro Texas
Posts: 367
|
Re: Add EGR Wiring to Aftermarket Harness
Like hugger said, if the egr has been deleted from the e prom I wouldn't worry about it. But if the ecm has never been messed with, just search the ecm number to find the proper PIN numbers and add them to your harness.
__________________
The bitterness of poor quality lingers long after the sweetness of a low price is forgotten. |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Sep 2009
Location: Visalia, CA
Posts: 247
|
Re: Add EGR Wiring to Aftermarket Harness
Thanks guys. Egr has not been removed from eprom. So just run the wires to the correct pins? No relays or anything like that? I don't know squat about wiring, so pardon my ignorance.
![]()
__________________
Coop34 70 Chevy C10 5.7L TBI/700R4 |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jul 2013
Location: Winnsboro Texas
Posts: 367
|
Re: Add EGR Wiring to Aftermarket Harness
The red wire should go to a 12v ign on power source and the other wire is grounded through the ecm. Look at your ecm and post the number and I can find you the wiring diagram.
__________________
The bitterness of poor quality lingers long after the sweetness of a low price is forgotten. |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Sep 2009
Location: Visalia, CA
Posts: 247
|
Re: Add EGR Wiring to Aftermarket Harness
I appreciate the help Acorn. ECM is 1227747.
__________________
Coop34 70 Chevy C10 5.7L TBI/700R4 |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jul 2013
Location: Winnsboro Texas
Posts: 367
|
Re: Add EGR Wiring to Aftermarket Harness
No problem. My memory is not as good as huggers so I had to look it up! I'm going off a 1990 k5 that I have with the 1227747 ecm.
Red wire- +12 volt fused Grey wire- to pin A4 on the ecm. The hardest part will be finding the wire terminal ends to go into the ecm plug...
__________________
The bitterness of poor quality lingers long after the sweetness of a low price is forgotten. |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jul 2013
Location: Winnsboro Texas
Posts: 367
|
Re: Add EGR Wiring to Aftermarket Harness
Yea... I just realized the pic I posted is to fuzzy to read...sorry.
Just google image search the ecm number. Should be able to find one you can read!
__________________
The bitterness of poor quality lingers long after the sweetness of a low price is forgotten. |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Sep 2009
Location: Visalia, CA
Posts: 247
|
Re: Add EGR Wiring to Aftermarket Harness
Found one. Thanks!
__________________
Coop34 70 Chevy C10 5.7L TBI/700R4 |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|