NV Buddy bucket(Drivers side)spacers/thick washers

[Chevy4Life]

Buddy bucket(Drivers side)spacers/thick washers $25.00 Shipped MERRY CHRISTMAS!

[1971 GMC Jimmy 2wd]

In line. Where do these go? From the seat to the bracket or the seat frame?

[Chevy4Life]

Originally Posted by 1971 GMC Jimmy 2wd

In line. Where do these go? From the seat to the bracket or the seat frame?

I don't remember off hand. I know it also levels out the drivers seat with the passengers side bracket height though.

[1971 GMC Jimmy 2wd]

I will check on my buddy buckets and see if I need them. Thanks

[402GMC]

Put me in line

[Cheyenne1970]

Put me in line as well.

[1971 GMC Jimmy 2wd]

I'll take them. Sending you a pm

[Chevy4Life]

Originally Posted by 1971 GMC Jimmy 2wd

I'll take them. Sending you a pm

PM returned...I think they go between the seat and slider.

[1971 GMC Jimmy 2wd]

I will pass

[Chevy4Life]

Originally Posted by 402GMC

Put me in line

You are up. 71 jimmy checked and has them already.

[Chevy4Life]

ttt

[Eagle9502]

Anyone confirm where these go?

[Chevy4Life]

Originally Posted by Eagle9502

Anyone confirm where these go?

I keep going back and forth in my head. There is a small lip on the frame that may need the clearance for the track to slide smooth. I'll go look at my other set right now.

[Chevy4Life]

Originally Posted by Chevy4Life

I keep going back and forth in my head. There is a small lip on the frame that may need the clearance for the track to slide smooth. I'll go look at my other set right now.

OK, That was zero help. My seats were redone in the 90's and like usual they are not right after they were taken apart. I have 2 by the door UNDER the frame(below the slider) and a few washers stacked UNDER the inner frame(below the slider). I KNOW this is incorrect.

So until I find out for sure I have 2 shipped for $12.50

[402GMC]

I'm I still up for all four?

[Chevy4Life]

Originally Posted by 402GMC

I'm I still up for all four?

Well you did reply before my revelation. So sure.

[69RDMo]

they go on the outside track, between the track and the seat frame, its because the way the frame is welded, if you look on the right side of the buddy seat, the inside track sits on top of the tube, and the outside track sits on the bracket. the slide hits the flat end of the tube thats welded to the bracket. i don't know that you'd need all four but i could be wrong. my seat was missing them. hope this helps. edit looks like you figured it out

[Chevy4Life]

Originally Posted by 69RDMo

they go on the outside track, between the track and the seat frame, its because the way the frame is welded, if you look on the right side of the buddy seat, the inside track sits on top of the tube, and the outside track sits on the bracket. the slide hits the flat end of the tube thats welded to the bracket. i don't know that you'd need all four but i could be wrong. my seat was missing them. hope this helps. edit looks like you figured it out

Yes. That's the lip I was talking about, the way the tube is flattened at the ends. Thanks for your help!

Also, I tried sliding my seat forward and it didn't move like it is.

Nice frame. Love the cup holders.

[Chevy4Life]

Never heard back from 402GMC so TTT

[davestrucks]

I can do $20.00 shipped.

[Chevy4Life]

Originally Posted by davestrucks

I can do $20.00 shipped.

Sure PM sent.

[davestrucks]

payment sent.