The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-29-2017, 11:11 PM   #1
reed62
Registered User
 
reed62's Avatar
 
Join Date: Apr 2016
Location: Denver CO
Posts: 129
Ididit Column Install

Hey all,
Has anyone else installed an Ididit steering column or Flaming River style? I have loosely put mine in to get an idea of how the column wiring harness will be routed and the possibility of notching the support bracket to clear the wiring. I am interested in what others have done to secure the column. The original column had 2 bolts that held the top end in place but the new Ididit column does not have provisions for that. Did anyone forgo the factory support bracket and use a column drop? Looking for ideas...

Thanks much...

Randy
reed62 is offline   Reply With Quote
Old 01-30-2017, 11:17 AM   #2
oldtrux
Registered User
 
oldtrux's Avatar
 
Join Date: Jul 2010
Location: Bancroft, ontario
Posts: 555
Re: Ididit Column Install

I just purchased an ididit column but havn't installed yet!it is the retrofit series and it does have the provisions for Bolt on just like original
I should add mine is a 66

Last edited by oldtrux; 01-30-2017 at 11:24 AM. Reason: Add comments
oldtrux is offline   Reply With Quote
Old 01-30-2017, 05:50 PM   #3
reed62
Registered User
 
reed62's Avatar
 
Join Date: Apr 2016
Location: Denver CO
Posts: 129
Re: Ididit Column Install

Quote:
Originally Posted by oldtrux View Post
I just purchased an ididit column but havn't installed yet!it is the retrofit series and it does have the provisions for Bolt on just like original
I should add mine is a 66
I see....mine is a generic column and only has the provisions for the turn signal lever, hazard button and tilt lever. I may have to fab a healthy strap to hold it up against the top of the bracket.
reed62 is offline   Reply With Quote
Old 01-30-2017, 06:05 PM   #4
The Rocknrod
Moderator

 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
Re: Ididit Column Install

If you don't have the retrofit series you might want to check the fit of the steering wheel, specifically the horn contact that goes through the wheel and is contacted by the horn ring. You may find it is too long.
The Rocknrod is offline   Reply With Quote
Old 01-30-2017, 08:40 PM   #5
62 Barnfind
Registered User
 
62 Barnfind's Avatar
 
Join Date: Jan 2012
Location: Killeen, Tx
Posts: 1,373
Re: Ididit Column Install

I just ordered one today for my 62. Reed 62 is yours for our year trucks? I hope I don't have to modify anything, I just want it to go in.
__________________
John Z
1962 Chevy C10 Stepside
62 Barnfind
My build tread: http://67-72chevytrucks.com/vboard/s...d.php?t=507513
62 Barnfind is offline   Reply With Quote
Old 01-30-2017, 09:49 PM   #6
64shortbox
Registered User
 
64shortbox's Avatar
 
Join Date: Jan 2011
Location: Tulare, CA
Posts: 734
Re: Ididit Column Install

Randy,
Maybe this will help. This is how I installed a 72 Chevy tilt Van column in my 64. I don't know if you can tell or not but I left the factory 72 van wiring underneath the column it the factory flat plastic conduit though it is painted to match in my picture. It clears the 64 E brake bracket without pinching just fine. Scroll down to post #4 to see how I did it.

http://67-72chevytrucks.com/vboard/s...d.php?t=711779
64shortbox is offline   Reply With Quote
Old 01-31-2017, 12:31 AM   #7
reed62
Registered User
 
reed62's Avatar
 
Join Date: Apr 2016
Location: Denver CO
Posts: 129
Re: Ididit Column Install

Quote:
Originally Posted by 62 Barnfind View Post
I just ordered one today for my 62. Reed 62 is yours for our year trucks? I hope I don't have to modify anything, I just want it to go in.
Hey Barnfind,
I ordered a generic column so it didn't have any holes or provisions to do an R and R style swap. I will have to do some fabbing I believe to secure it. The fitment is fine, it just doesn't have any threaded bungs to hook it up to the stock brackets.
reed62 is offline   Reply With Quote
Old 01-31-2017, 12:32 AM   #8
vin63
It's Better With Nitro
 
vin63's Avatar
 
Join Date: Apr 2008
Location: Chino Hills, CA
Posts: 2,262
Re: Ididit Column Install

Here's how I installed my Ididit column...



__________________
1963 C-10: Deluxe-optioned cab, shortbed, fleetside
Pontiac 462 ci, Kauffman D-Port alum. heads
4L80E, narrowed sheetmetal Ford 9-inch
Tubular front and rear suspension
Custom 6-piston front disc and 4-piston rear disc brakes
vin63 is offline   Reply With Quote
Old 01-31-2017, 12:33 AM   #9
reed62
Registered User
 
reed62's Avatar
 
Join Date: Apr 2016
Location: Denver CO
Posts: 129
Re: Ididit Column Install

Quote:
Originally Posted by 64shortbox View Post
Randy,
Maybe this will help. This is how I installed a 72 Chevy tilt Van column in my 64. I don't know if you can tell or not but I left the factory 72 van wiring underneath the column it the factory flat plastic conduit though it is painted to match in my picture. It clears the 64 E brake bracket without pinching just fine. Scroll down to post #4 to see how I did it.

http://67-72chevytrucks.com/vboard/s...d.php?t=711779

Thanks 64shortbox,
I will check it out. I am not looking at a very difficult situation, I will just have to do a little work to make sure it is secure and functional.
reed62 is offline   Reply With Quote
Old 01-31-2017, 01:02 AM   #10
The Rocknrod
Moderator

 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
Re: Ididit Column Install

Quote:
Originally Posted by vin63 View Post
Here's how I installed my Ididit column...
Do you remember which Ididit column you used?
Did you drill the holes in the column yourself?
Did you use a stock steering wheel?
How long is the column?
The Rocknrod is offline   Reply With Quote
Old 01-31-2017, 09:45 AM   #11
vin63
It's Better With Nitro
 
vin63's Avatar
 
Join Date: Apr 2008
Location: Chino Hills, CA
Posts: 2,262
Re: Ididit Column Install

It's the Ididit Retrofit column for our trucks. Mine is the older model that did not come with the adjustable threaded mounts, so I had to drill and install nutcerts - I used the 4 mount holes in the handbrake mount. I see a lot of others just use two fasteners in the forward attachment slots of the column/handbrake mount. This is my steering wheel that uses the deluxe hub:

__________________
1963 C-10: Deluxe-optioned cab, shortbed, fleetside
Pontiac 462 ci, Kauffman D-Port alum. heads
4L80E, narrowed sheetmetal Ford 9-inch
Tubular front and rear suspension
Custom 6-piston front disc and 4-piston rear disc brakes
vin63 is offline   Reply With Quote
Old 01-31-2017, 09:50 AM   #12
The Rocknrod
Moderator

 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
Re: Ididit Column Install

Looks awesome, great steering wheel. Thanks.
The Rocknrod is offline   Reply With Quote
Old 02-01-2017, 07:00 AM   #13
AUS64c10
Registered User
 
Join Date: Feb 2013
Location: Melbourne, Australia
Posts: 88
Re: Ididit Column Install

I thought the factory steering wheel didn't fit on the ididit columns. I would love to fit my deluxe steering wheel if possible.
AUS64c10 is offline   Reply With Quote
Old 02-01-2017, 11:55 AM   #14
vin63
It's Better With Nitro
 
vin63's Avatar
 
Join Date: Apr 2008
Location: Chino Hills, CA
Posts: 2,262
Re: Ididit Column Install

The splines should be the same.
__________________
1963 C-10: Deluxe-optioned cab, shortbed, fleetside
Pontiac 462 ci, Kauffman D-Port alum. heads
4L80E, narrowed sheetmetal Ford 9-inch
Tubular front and rear suspension
Custom 6-piston front disc and 4-piston rear disc brakes
vin63 is offline   Reply With Quote
Old 02-02-2017, 03:22 PM   #15
reed62
Registered User
 
reed62's Avatar
 
Join Date: Apr 2016
Location: Denver CO
Posts: 129
Re: Ididit Column Install

Quote:
Originally Posted by vin63 View Post
It's the Ididit Retrofit column for our trucks. Mine is the older model that did not come with the adjustable threaded mounts, so I had to drill and install nutcerts - I used the 4 mount holes in the handbrake mount. I see a lot of others just use two fasteners in the forward attachment slots of the column/handbrake mount. This is my steering wheel that uses the deluxe hub:

Hey Vin63,
Do you remember what size nutsert you used?
reed62 is offline   Reply With Quote
Old 02-02-2017, 03:29 PM   #16
vin63
It's Better With Nitro
 
vin63's Avatar
 
Join Date: Apr 2008
Location: Chino Hills, CA
Posts: 2,262
Re: Ididit Column Install

I used 1/4-20.

Quote:
Originally Posted by reed62 View Post
Hey Vin63,
Do you remember what size nutsert you used?
__________________
1963 C-10: Deluxe-optioned cab, shortbed, fleetside
Pontiac 462 ci, Kauffman D-Port alum. heads
4L80E, narrowed sheetmetal Ford 9-inch
Tubular front and rear suspension
Custom 6-piston front disc and 4-piston rear disc brakes
vin63 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:39 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com