350/400 SB heads needed near PA

[67ChevyC10Stepside]

i have a 350 short block and a 400 short block...i have one set of heads....i need another.....needs to be close to me cause shipping would probably suck. let me know what you got

[67ChevyC10Stepside]

ttt

[67ChevyC10Stepside]

ttt

[ScottH]

What r u looking for in the heads? Redone or used, 64 vs 76 cc, small valve vs large, etc. Let me know and I'll see what I have.

Thanks.

Scott

[67ChevyC10Stepside]

anything you got....if i buy high performers they will go on my 400 if i buy plain janes they will go on the 350 let me know what you got

[67ChevyC10Stepside]

ttt

[67ChevyC10Stepside]

ttt

[67ChevyC10Stepside]

you still there? im plannin on making a trip to NJ so if you have them that would be great!

[67ChevyC10Stepside]

68 hits and one person has heads? hmm

[Fast67velle]

I might have a set of 400 heads somewhere. I have to look through all of these! They are bone stock with the steam holes! I'll get back to you. PM ME

[67ChevyC10Stepside]

any of those 64cc? i would kinda like high CR

[racewithem]

Actually shipping is not to bad for a set of heads. It's like 40$'s or something. Only problem is you can't see the heads until you paid for them and recieved them and if you don't like them you are stuck. I have made out on a few deals and lost on a few more. A 400 head is only a 350 head that has ben drilled. You can do this yourself. Just put the 400 gasket on the 350 head and drill where the steam hole in the gasket is. Most times it is cheaper to buy a new set than to buy and recondition an old set. At least then they are new and you know they are good. Since you seem to be in a hurry here is a few sites to look for heads on.

For new

http://www.gmpartsdepot.com/store/ca...Category_ID=65 A new set of Vortecs complete with valves and springs about $500.

http://www.sdpc2000.com/cart.asp?act...tart&catid=277

For Used
https://www.redneckjunk.com/Classifi...Classified.asp


http://www.mortec.com/

http://www.racecarauctions.com/

http://www.aarn.com/

http://oval.race-cars.com/

http://www.rpmstreet.com/cgi-bin/cla...lassifieds.cgi

http://www.raceindustry.com/

http://www.jrmotorsports.net/

http://www.autopartx.com/

http://www.nepitstop.com/index.jsp

I probably have more somewhere but this should keep you busy for a few minutes.

[67ChevyC10Stepside]

i just want an old set of 64cc i think 434 casting heads

[67ChevyC10Stepside]

ttt

[67ChevyC10Stepside]

you dont have to be mean about it and you dont need the attitude....i dont know much about them and im not sure what to look for....i know i want 64cc the one with the 202 intake valve......that's all i know oh and i think they are called 434s

[Ont67shortbox]

I have a set of 400 small block heads casting number is 3973493, you can have them for $200.00 i am in Ontario halfway between Detroit and Toronto

[67ChevyC10Stepside]

what kinda shape they in? any pics?

[Ont67shortbox]

I don't have a digital camera,they are off of a 400 with approx 5000 miles on it,I also have a set of Sportsman 2's fully ported,for $800.00 a set of angle plug *492* cast for $500 unassembled, and a nice Offy dual 4 bbl setup with twin Carter 500cfm carbs and edelbrock air cleaners, new for $800.00,come have a look if you want and we can work out a deal, i need room in my garage lol, Brian

[67ChevyC10Stepside]

you live a little far away for me to "come take a look" lol.......

[67ChevyC10Stepside]

ttt

[Ont67shortbox]

Yeah i guess its about 6 hrs,not sure where Butler Pa is.but i am 2 hrs from Detroit, and 2 1/2 hrs from Buffalo,

[67ChevyC10Stepside]

ttt

[67ChevyC10Stepside]

ttt