The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1969 - 1972 Blazers and Jimmys Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-28-2004, 12:57 AM   #1
72jimmy4x4
Registered User
 
Join Date: Feb 2004
Location: Victoria B.C.
Posts: 101
Body shims

Did the bodys of your jimmys come with body shims to line up the doors so they will close properley?
Thanks for any help
72jimmy4x4 is offline   Reply With Quote
Old 04-28-2004, 02:16 AM   #2
Jimmy72custom
Registered User
 
Jimmy72custom's Avatar
 
Join Date: Apr 2004
Location: Willits Ca
Posts: 261
Yes you can shim the body, but I would check your body mounts, door hinges, the pin is not to hard to replace. Then try to adjust the door and striker. Sometimes the problem is rotten pillar base and cab support, it will cause the Jimmy to sag. It is hard to tell what might be bad under the rocker panels.

Jimmy72custom is offline   Reply With Quote
Old 04-28-2004, 02:51 AM   #3
Alexis
Member since 2000
 
Alexis's Avatar
 
Join Date: Dec 2000
Location: Mountain View Ca / Mexico
Posts: 7,874
i don't think I've seen a door shimmed before, cowl and fender, yes. But like Jimmy said check the body for rust especially the under side.
Alexis is offline   Reply With Quote
Old 04-28-2004, 03:31 PM   #4
JayDubBlazer
go cyclones
 
JayDubBlazer's Avatar
 
Join Date: Jun 2003
Location: Ames, IA
Posts: 1,883
shims under the body or the shim-like things that are on the body in the door way.
__________________
Wes



PROJECT OLE GREEN

1972 Blazer 4X4 350/700R4
2017 Silverado LT
JayDubBlazer is offline   Reply With Quote
Old 04-28-2004, 07:39 PM   #5
Tonyp
Registered User
 
Tonyp's Avatar
 
Join Date: Dec 2003
Location: So Cal
Posts: 179
what I did was use a flat washers and cut a slot from the outter edge to the center hole, that way all I needed to do was loosen up the bolt (not remove it) and slide the washer in. Some of the bolts are welded in and if you have carpet you would have to remove things to get them out...so try the "C" washer...
__________________
72 K/5
350/205
SOFT-TOP
DOUG THORLEY HEADERS
A/C
CUSTOM REAR BUMPER
http://www.socalbigdawgs.com/tr/7.18.03/DSC04290.JPG
Tonyp is offline   Reply With Quote
Old 04-28-2004, 10:20 PM   #6
Gary 70 Jimmy
Senior Member

 
Gary 70 Jimmy's Avatar
 
Join Date: Jan 2002
Location: Burghill, Ohio 44404
Posts: 3,401
You can buy the big flat washers with the cut out allready their but I dont know who sells them I need some for my jimmy Does anyone no where you can get them.
Gary 70 Jimmy is offline   Reply With Quote
Old 04-28-2004, 11:06 PM   #7
Alexis
Member since 2000
 
Alexis's Avatar
 
Join Date: Dec 2000
Location: Mountain View Ca / Mexico
Posts: 7,874
most auto parts store carry shim. Any local automotive paint shop should have them and different sizes in thickness.
Alexis is offline   Reply With Quote
Old 04-29-2004, 12:54 AM   #8
72jimmy4x4
Registered User
 
Join Date: Feb 2004
Location: Victoria B.C.
Posts: 101
Just got in the house from shimming body mounts 2 & 3 to get the doors to close properley. I had changed them all and fastened her all up to find the doors did not close to well. The old mounts were very bad some the bolts were just rattling around in there but the doors did close with out a hitch.
72jimmy4x4 is offline   Reply With Quote
Old 05-01-2004, 08:22 AM   #9
Huck
Senior Member
 
Huck's Avatar
 
Join Date: Jun 2001
Location: Shelbyville, KY
Posts: 3,261
the GM book talks to shims to the mounts during the initial build process for door alignment so even with perfect inner rocker boxes, you may have to shim with new rubber mounts!!!
Huck is offline   Reply With Quote
Old 05-07-2004, 11:11 PM   #10
FRENCHBLUE72
PROJECT 7DEUCE
 
FRENCHBLUE72's Avatar
 
Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,606
I had a similar problem when I put new urethane mount's on my blazer and could not get the door's to shut a little shiming on th ebody mount behind the door's and now they close great..
__________________
GO BIG GREEN GO DUCKS



MEMBER #6377

72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free.

Project "7DEUCE"

check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665



Tim Powell..R.I.P EastSideLowlife..... R.I.P..
FRENCHBLUE72 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:19 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com