Bumper guards - Help identify - might sell - The 1947 - Present Chevrolet & GMC Truck Message Board Network

FrankHoy · 05-11-2004, 03:39 PM

I found a set of new bumper gaurds and need some help identifying the possible year. They almost match up on my 72 Cheyenne but have a little bit of a gap, shown where the red circles are. These have a smaller secondary indented area, below the main top ridge, where my older set is smooth. So, I believe these may be for 73 up? They both are stamped, on the back, with 914R

Can anyone help?

And finally, 100 WooHoo

72dually · 05-11-2004, 10:58 PM

could I see the face of the rubber, and picture of the backside?

FrankHoy · 05-11-2004, 11:27 PM

Here both views.

72dually · 05-12-2004, 12:02 AM

Hmmm, sorry Im stumped

cmchevyguy72 · 05-12-2004, 08:45 PM

a 68 chevy

pickupman · 05-12-2004, 08:54 PM

They sorta look like a set that came on a 71 blazer that I had. They were a dealer add on and not factory. Didn't conform to the bumper, had a long bracket that went back and hook on bottom of bumper. I think I still have them. I will have to check to see if they are the same.

05-11-2004, 03:39 PM	#1
FrankHoy Registered User Join Date: Aug 2002 Location: Des Moines, IA Posts: 154	Bumper guards - Help identify - might sell I found a set of new bumper gaurds and need some help identifying the possible year. They almost match up on my 72 Cheyenne but have a little bit of a gap, shown where the red circles are. These have a smaller secondary indented area, below the main top ridge, where my older set is smooth. So, I believe these may be for 73 up? They both are stamped, on the back, with 914R Can anyone help? And finally, 100 WooHoo Attached Images __________________ 72 Cheyenne 2wd LWB 402/350 CC/PS/PB/AC Tilt/Tach (upgrading to 4X4 402/700R4 CC/PS/PB/AC Tilt/Tach PW/PL) 71 Custom Deluxe 350/350 Tilt/PS/PB 00 Blazer Last edited by FrankHoy; 05-11-2004 at 03:52 PM.

05-11-2004, 11:27 PM	#3
FrankHoy Registered User Join Date: Aug 2002 Location: Des Moines, IA Posts: 154	Here both views. Attached Images __________________ 72 Cheyenne 2wd LWB 402/350 CC/PS/PB/AC Tilt/Tach (upgrading to 4X4 402/700R4 CC/PS/PB/AC Tilt/Tach PW/PL) 71 Custom Deluxe 350/350 Tilt/PS/PB 00 Blazer

05-12-2004, 08:54 PM	#6
pickupman Registered User Join Date: Dec 2000 Location: Greeneville, TN Posts: 3,097	They sorta look like a set that came on a 71 blazer that I had. They were a dealer add on and not factory. Didn't conform to the bumper, had a long bracket that went back and hook on bottom of bumper. I think I still have them. I will have to check to see if they are the same. __________________ atheystruck@comcast.net 67 1/2 ton 4wd custom cab 72 1/2 ton 4wd super cheyenne 71 1/2 BB super cheyenne shortbed

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-11-2004, 10:58 PM	#2
72dually Senior Member Join Date: Apr 2004 Location: Northern Arizona Posts: 687	could I see the face of the rubber, and picture of the backside?

05-12-2004, 12:02 AM	#4
72dually Senior Member Join Date: Apr 2004 Location: Northern Arizona Posts: 687	Hmmm, sorry Im stumped

05-12-2004, 08:45 PM	#5
cmchevyguy72 Registered User Join Date: Apr 2004 Location: iowa Posts: 27	a 68 chevy



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.