|
01-15-2019, 05:41 AM
|
#1 |
|
Senior Member
 Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,508
|
Rag joint bolts
Does anyone know what size the bolts that hold the rag joint to the steering box are?
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
|
|
|
01-15-2019, 06:01 AM
|
#2 |
|
Registered User
Join Date: May 2017
Location: Seatac, wa
Posts: 172
|
Re: Rag joint bolts
Buy it from lmc because their is only one bolt out of the 3 if i remember and be prepared to drill out the ones that aren't bolts unless you're taking out your steering column
|
|
|
|
|
01-15-2019, 09:17 AM
|
#3 |
|
Senior Member
Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,508
|
Re: Rag joint bolts
The steering column is out and I just need the bolts. LMC doesn't have them separately. I thought if I could get the size I could buy them locally.
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
|
|
|
|
01-15-2019, 09:21 AM
|
#4 |
|
Senior Member
Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,508
|
Re: Rag joint bolts
Just to clarify, I am looking for the bolts that hold the rag joint to the steering column shaft.
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
|
|
|
|
01-15-2019, 10:10 AM
|
#5 |
|
Senior Member
Join Date: Mar 2012
Location: Chesapeake, Va
Posts: 1,275
|
Re: Rag joint bolts
Can you go to a parts store and check the Dorman (help) Section for the correct ones? I thought mine had splines in the shoulders,for a special fastener
if i remember right??? but do not quote me on that .....
__________________
Mike 72 C-10 Cheyenne off frame resto and Upgraded to 4 wheel disk, Tilt, Dakota Digital Dash / Rear slider. 421 SBC / TH350 3000RPM Stall Progression Ignition /Holley 750 DP/3:73 gear Eaton Limited Slip unit / 2 1/2 exhaust glasspacks 
|
|
|
|
|
01-15-2019, 01:15 PM
|
#6 |
|
Senior Member
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,598
|
Re: Rag joint bolts
If you are talking the pinch bolt.....Factory uses a 12 point headed bolt. You can use an allen head style. 3/8'' fine thread, 1-1/4'' long , should be grade 8
|
|
|
|
|
01-15-2019, 04:23 PM
|
#7 |
|
Senior Member
Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,508
|
Re: Rag joint bolts
Sorry, guys. These are the bolts I am trying to size.
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
|
|
|
|
01-15-2019, 05:10 PM
|
#8 |
|
Registered User
Join Date: May 2017
Location: Seatac, wa
Posts: 172
|
Re: Rag joint bolts
save yourself the time and order the complete setup
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
