Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
07-29-2020, 02:02 AM | #1 |
Senior Member
Join Date: Dec 1999
Location: Southern California
Posts: 2,881
|
Tailgate link/arm bumpers
Could someone measure the location of these for me? Need to re-drill the location. With all the screw holes in the rear stake pillars guess I ended up welding up the holes.
__________________
Richard 1972 K10 Custom Deluxe SWB Fleetside My build https://67-72chevytrucks.com/vboard/...d.php?t=800746 |
07-30-2020, 09:16 PM | #2 |
Senior Member
Join Date: Dec 1999
Location: Southern California
Posts: 2,881
|
Re: Tailgate link/arm bumpers
No one?
__________________
Richard 1972 K10 Custom Deluxe SWB Fleetside My build https://67-72chevytrucks.com/vboard/...d.php?t=800746 |
07-30-2020, 10:40 PM | #3 |
Senior Member
Join Date: Dec 1999
Location: Spring Valley, Ca.
Posts: 1,136
|
Re: Tailgate link/arm bumpers
The thick one by my eye measures 7 3/8" up from the lower end the stake pillar and 1/2" in from the outer brake radius. The small button one on top should be drilled in the middle of the depression.
__________________
Smitty '71 Short Fleetside Spring Valley, Ca. |
07-31-2020, 02:35 AM | #4 |
Senior Member
Join Date: Dec 1999
Location: Southern California
Posts: 2,881
|
Re: Tailgate link/arm bumpers
Thank you for taking the time. I am good with the button bumper. Is the measurement to the edge of the rectangular bumper or to center where screw attachment is?
__________________
Richard 1972 K10 Custom Deluxe SWB Fleetside My build https://67-72chevytrucks.com/vboard/...d.php?t=800746 |
07-31-2020, 07:35 AM | #5 |
Senior Member
Join Date: Dec 1999
Location: Spring Valley, Ca.
Posts: 1,136
|
Re: Tailgate link/arm bumpers
Should be to center. As close as I could see to a hole in a rubber block. Let me go out and double check this morning when there is better light. Last night was with a flashlight. I’ll post measurements again. Was using a machinist square and the increments are so close. With poorer light they may be off a bit. I measured from where the stake fitting meets the rear sill plate.
__________________
Smitty '71 Short Fleetside Spring Valley, Ca. |
07-31-2020, 08:09 AM | #6 |
Registered User
Join Date: Jul 2015
Location: Sedalia Mo.
Posts: 1,131
|
Re: Tailgate link/arm bumpers
8 1/2 inches down from the buttonhole. 1 inch in from the inner face of the stake pocket to the hole (hole-center) for the square bumper.
__________________
He who is without oil shall throw the first rod. Compressions 8.7:1 1972 C10 1976 C10 (parts truck) 1985 K20 Last edited by sick472; 07-31-2020 at 12:02 PM. Reason: Added the word "hole-center" to be clear |
07-31-2020, 11:34 AM | #7 |
Senior Member
Join Date: Dec 1999
Location: Spring Valley, Ca.
Posts: 1,136
|
Re: Tailgate link/arm bumpers
Richard
Remeasured a little while ago. The 7 3/8 dimension is good. As is 472's, just taken from a different dimension. As for the other mine measures 1/2 in to center. Not sure if 472 was measuring to center of hole or outside of the bumper. But if he measured to the outside of the bumper both dimensions would be the same.
__________________
Smitty '71 Short Fleetside Spring Valley, Ca. |
08-01-2020, 12:44 AM | #8 |
Senior Member
Join Date: Dec 1999
Location: Southern California
Posts: 2,881
|
Re: Tailgate link/arm bumpers
Thank you both for this.
__________________
Richard 1972 K10 Custom Deluxe SWB Fleetside My build https://67-72chevytrucks.com/vboard/...d.php?t=800746 |
08-01-2020, 08:47 AM | #9 |
Senior Member
Join Date: Dec 1999
Location: Spring Valley, Ca.
Posts: 1,136
|
Re: Tailgate link/arm bumpers
Sorry I was slow, but glad I could help.
__________________
Smitty '71 Short Fleetside Spring Valley, Ca. |
08-02-2020, 04:15 AM | #10 |
Senior Member
Join Date: Dec 1999
Location: Southern California
Posts: 2,881
|
Re: Tailgate link/arm bumpers
NP, will not fit tailgate until next week. Thanks again to you and sick472 who took the time to do this for me.
__________________
Richard 1972 K10 Custom Deluxe SWB Fleetside My build https://67-72chevytrucks.com/vboard/...d.php?t=800746 |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|