1963 L60 10 lug , want 22.5" wheels - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**aerotruk63** · 07-22-2023, 04:29 PM

Anyone have a set of 22.5" x 6.00 or 6.75 wheels.
10 on 8.75 with 6.25 centerbore.
1960-1987 GM trucks C50 or C60 schoolbus later RV'S.

**CarolinaHD** · 07-22-2023, 06:14 PM

You and everyone else in North America with these trucks are looking for those wheels. Few and far in-between nowadays. I looked for 3 years and still only managed to get a set of 4 original wheels. Had to order 2 reproduction wheels from Wheels Now. That's who I would contact.

**JPBrecheisen** · 08-18-2023, 05:54 PM

Same.

I only ended up finding two and ended up just getting the ones from wheels now.

**CarolinaHD** · 08-18-2023, 07:44 PM

Quote:

Originally Posted by JPBrecheisen

Same.

I only ended up finding two and ended up just getting the ones from wheels now.

Were the wheel studs on the rear axle too short with the aftermarket wheels? I've read about some guys running into issues due to the aftermarket wheels being thicker than originals. I used 1 original and 1 aftermarket on my rear end and the stud is flush with the lugnut.

**JPBrecheisen** · 08-18-2023, 08:22 PM

I did run into the stud issue but only by a thread.

I keep an eye on them and have considered a shallower modern nut with the washer built in.

I don't run mine a lot but so far, no issues.

07-22-2023, 04:29 PM	#1
aerotruk63 Check The Champ, Demonstrator Join Date: Jun 2009 Location: Montreal,Quebec Posts: 6,627	1963 L60 10 lug , want 22.5" wheels Anyone have a set of 22.5" x 6.00 or 6.75 wheels. 10 on 8.75 with 6.25 centerbore. 1960-1987 GM trucks C50 or C60 schoolbus later RV'S. __________________ 1963 *Chevrolet Truck* Literature LINK: https://picasaweb.google.com/113840717762774560215 YouTube Channel with 20+ Original *Chevrolet Truck* Salesmen, Mechanics & Service Department Training Slideshows. https://www.youtube.com/results?sear...otruk63&page=1

07-22-2023, 06:14 PM	#2
CarolinaHD Moderator Join Date: Aug 2017 Location: Cabarrus Posts: 417	Re: 1963 L60 10 lug , want 22.5" wheels You and everyone else in North America with these trucks are looking for those wheels. Few and far in-between nowadays. I looked for 3 years and still only managed to get a set of 4 original wheels. Had to order 2 reproduction wheels from Wheels Now. That's who I would contact. __________________ Alex 1967 C50 292ci Lumber truck 1967 C50 292ci Dump truck 1967 C60 366ci Fire truck

08-18-2023, 05:54 PM	#3
JPBrecheisen Senior Member Join Date: Jul 2012 Location: Harrisville, New York Posts: 459	Re: 1963 L60 10 lug , want 22.5" wheels Same. I only ended up finding two and ended up just getting the ones from wheels now. __________________ 1960 GMC K1500 LB Fleet Side 1962 GMC K1000 LB Step Side 1988 Chevrolet C2500

08-18-2023, 08:22 PM	#5
JPBrecheisen Senior Member Join Date: Jul 2012 Location: Harrisville, New York Posts: 459	Re: 1963 L60 10 lug , want 22.5" wheels I did run into the stud issue but only by a thread. I keep an eye on them and have considered a shallower modern nut with the washer built in. I don't run mine a lot but so far, no issues. Attached Images __________________ 1960 GMC K1500 LB Fleet Side 1962 GMC K1000 LB Step Side 1988 Chevrolet C2500

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.