How To Change The Cab Mount Isolators? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

69sixpackbee · 08-16-2004, 12:37 PM

I noticed while I was on vacation that My camper looked crooked over the cab of my truck. Well, since the bed is bolted directly to the frame this only led me to think that the cab was leaning a bit. Sure enough, the pass side rear rubber was collapsed about one-half inch. Now then, can these be replaced without removing the cab from the frame?

*FormerMember* · 08-16-2004, 01:05 PM

Yes, if you can get the bolts out without breaking them off...

I will soak them with PB Blaster for a couple of days then do one side at a time.

Loosen the opposite side, remove all the bolts on the side you're working on. Jack up with a 2x4 across the entire cab. Replace and leave 'em loose.

Do the other side and tighten em all down.

69sixpackbee · 08-16-2004, 01:28 PM

Sounds easy. Thanx!

avejoe · 08-16-2004, 02:04 PM

I just did this on my truck and it took about 2 hours. It's really easy. Most of my time was spent messing with a bottle jack and 4x4's as my floor jack is "jacked". Don't forget to loosen the radiator support mounts before you jack up the cab.

*FormerMember* · 08-16-2004, 02:12 PM

the radiator supports came in the kit I bought. So those got done, too

**ScottH** · 08-16-2004, 02:33 PM

This may be a dump question, but do u need to loosen the radiator support bolts if you only want to change out the cab mounts?

Thanks.

toddtheodd · 08-16-2004, 02:45 PM

Your Question:

Quote:

This may be a dump question, but do u need to loosen the radiator support bolts if you only want to change out the cab mounts?

Posted in this thread just before yous:

Quote:

Don't forget to loosen the radiator support mounts before you jack up the cab.

**ScottH** · 08-16-2004, 02:49 PM

Thanks, I noticed that which is why I asked. I need to replace one or two (temporary fix) cab mounts and was wondering if it is necessary to loosen the radiator support bolts to do so. I wasn't sure he mentioned it in the post as replacing them at the same time, or to loosen them to make changing of the cab mounts easier (and not screw up anything up front).

Scott

*FormerMember* · 08-16-2004, 04:20 PM

Quote:

Originally Posted by ScottH

Thanks, I noticed that which is why I asked. I need to replace one or two (temporary fix) cab mounts and was wondering if it is necessary to loosen the radiator support bolts to do so. I wasn't sure he mentioned it in the post as replacing them at the same time, or to loosen them to make changing of the cab mounts easier (and not screw up anything up front).

Scott

I'd loosen every mount bolted to the cab and fenders, to give you enough clearance. Also, don't wimp out on us now. Do them all :p

08-16-2004, 12:37 PM	#1
69sixpackbee Registered User Join Date: Jan 2001 Location: Sabinal, Texas Posts: 1,706	How To Change The Cab Mount Isolators? I noticed while I was on vacation that My camper looked crooked over the cab of my truck. Well, since the bed is bolted directly to the frame this only led me to think that the cab was leaning a bit. Sure enough, the pass side rear rubber was collapsed about one-half inch. Now then, can these be replaced without removing the cab from the frame?

08-16-2004, 02:04 PM	#4
avejoe Custer had a plan too. Join Date: Dec 2003 Location: No. California Posts: 344	Cab Mount Replacement I just did this on my truck and it took about 2 hours. It's really easy. Most of my time was spent messing with a bottle jack and 4x4's as my floor jack is "jacked". Don't forget to loosen the radiator support mounts before you jack up the cab.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-16-2004, 01:05 PM	#2
FormerMember Account Suspended Join Date: Feb 2004 Posts: 3,051	Yes, if you can get the bolts out without breaking them off... I will soak them with PB Blaster for a couple of days then do one side at a time. Loosen the opposite side, remove all the bolts on the side you're working on. Jack up with a 2x4 across the entire cab. Replace and leave 'em loose. Do the other side and tighten em all down.

08-16-2004, 01:28 PM	#3
69sixpackbee Registered User Join Date: Jan 2001 Location: Sabinal, Texas Posts: 1,706	Sounds easy. Thanx!

08-16-2004, 02:12 PM	#5
FormerMember Account Suspended Join Date: Feb 2004 Posts: 3,051	the radiator supports came in the kit I bought. So those got done, too

08-16-2004, 02:33 PM	#6
ScottH Senior Member Join Date: Sep 2002 Location: Hampstead, NC Posts: 8,187	This may be a dump question, but do u need to loosen the radiator support bolts if you only want to change out the cab mounts? Thanks.

08-16-2004, 02:49 PM	#8
ScottH Senior Member Join Date: Sep 2002 Location: Hampstead, NC Posts: 8,187	Thanks, I noticed that which is why I asked. I need to replace one or two (temporary fix) cab mounts and was wondering if it is necessary to loosen the radiator support bolts to do so. I wasn't sure he mentioned it in the post as replacing them at the same time, or to loosen them to make changing of the cab mounts easier (and not screw up anything up front). Scott



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.