![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
lets play the number game....again
Picked up my 350 yesterday, now it is time to tace the origins of it. Can y'all hook me up? I still have absolutly no luck with this crap. I remember some one told me to call some one up, but I can't remember whom to call, nor do I have a number.
![]() On the pad up front on the passenger side... 1M0528 And directly under that one is 6VP Then on the bellhousing, hecho en Mexico...I know what that means... then under that 10066036 I know it is a 4 bolt main, newer (painted black, passenger dipstick) casting, Pretty sure it is a 350...I don't think anything else came in 4 bolt in the later engines...or was there a 4 bolt 305? ![]() The heads, are also hecho en Mexico...scalloped lower edge, so I know they are a light weight casting...the intake looks pretty friggen huge, and I was told it was 2.02...but they may well be 1.94's...my eyes haven't been calibrated lately. ![]() Anyone have anything for me? I'm going to put new rod/main bearings, hone it out, new rings a good cleaning....debating on a cam or not....trying to go low buck here, and it just isn't adding up to low buck. The bore has absolutly no ridge in it at all. Last edited by Longhorn Man; 10-19-2004 at 09:32 PM. |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: May 2000
Location: Flin Flon, Manitoba, Canada
Posts: 8,855
|
10066036...350...........2 or 4...Target Master/Goodwrench crate motor, 2-piece rear
seal, "Hecho en Mexico
__________________
My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795 |
![]() |
![]() |
![]() |
#3 |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,477
|
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
![]() |
![]() |
![]() |
#4 | |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,477
|
Quote:
DAMN, BEAT ME BY LIKE 2 SECONDS. ![]()
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
![]() |
![]() |
![]() |
#5 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
did I list a date code there by chance...or is there not going to be one?
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: May 2000
Location: Flin Flon, Manitoba, Canada
Posts: 8,855
|
10054727...350...86-up...2 or 4...one piece rear seal, some "Made in Canada"
10066036...350...........2 or 4...Target Master/Goodwrench crate motor, 2-piece rear seal, "Hecho en Mexico" 10066038...350.....92....4...Goodwrench crate motor, 2-piece rear seal, "Hecho en Mexico" If it follows sequence, looks to be an 86 and up
__________________
My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795 |
![]() |
![]() |
![]() |
#7 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Sweet...you guys rock.
i had forgotten that link...mortec is easier to use than nasty z28...but without the list of andy's favorites, I am lost. How about the heads, any luck with them? Are they decent, best of the worst, worst of the worst? |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: May 2000
Location: Flin Flon, Manitoba, Canada
Posts: 8,855
|
got a head casting # for us?
__________________
My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795 |
![]() |
![]() |
![]() |
#9 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
The heads, are also hecho en Mexico...scalloped lower edge, so I know they are a light weight casting...the intake looks pretty friggen huge, and I was told it was 2.02...but they may well be 1.94's...my eyes haven't been calibrated lately. The head number was hard to make out....969...968....or 369. I think the last one is correct, but I am not 100% sure.
|
![]() |
![]() |
![]() |
#10 |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,477
|
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Mar 2004
Location: Corinth,TX
Posts: 444
|
This is what i found on the heads....
33417369...90-up...350..........Gen.I Goodwrench crate motor,"Hecho en Mexico", 76cc |
![]() |
![]() |
![]() |
#12 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
76 cc...i like cheap gas...low compression heads will let me burn the cheap stuff.
Oh well...I'm just slappin it together to sell it. Thanks again y'all. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|