![]() |
![]() |
#1 |
Garage Queen Material
Join Date: Oct 2002
Location: USA
Posts: 4,129
|
wheel spacers?
anybody know if it woudl be a good idea to use wheel spacers on our trucks? i hate the way the back tires stick so much farther in than the front ones.
where would be a good place to buy some, and what type would i need and what size? |
![]() |
![]() |
![]() |
#2 |
www.73-87chevytrucks.com
![]() Join Date: Dec 1999
Location: Birmingham, AL
Posts: 6,935
|
SCOTI is using them. Not sure where they came from, but they are adapters to change the lug pattern. The rear is about 4" narrower (2" per side).
__________________
Chris Lucas 1973 Chevy C-10 1978 GMC Jimmy (2WD) - SOLD 1987 R10 twin turbo LS 1991 R3500 SRW CrewCab 1985 K5 diesel swapped project 1989 K5 2WD conversion w/ Vette susp Project Captkaos Customs 73-87chevytrucks.com |
![]() |
![]() |
![]() |
#3 |
Senior Member
Join Date: Mar 2003
Posts: 2,500
|
There has been alot of failures with spacers in the past.
I wouldn't trust them. |
![]() |
![]() |
![]() |
#4 |
Workaholic
Join Date: Oct 2002
Location: Katy, TX
Posts: 1,589
|
I hate this too and I think spacers would be fine for everyday driving but I wouldn't use them if I were at the strip or heavy off road use.
|
![]() |
![]() |
![]() |
#5 |
Under construction!
Join Date: Aug 2002
Location: NorCal
Posts: 1,065
|
I would avoid wheel spacers and adapters at all costs.
![]()
__________________
2001 Silverado bagged on 22's. *Sold* |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: May 2003
Location: Lake Oswego, Oregon
Posts: 1,028
|
wheel spacers are trouble. there is only one way i would go about fixing your problem by getting the correct backspaced wheels. i know it might sound spendy, but nothing close to what it will cost you for new bed sides, hub rebuild, paint and bodywork when your wheel plops off.
__________________
Ken Morgan For fun: 1964 Volvo 122 For slow: 1984 Chevrolet C-10 For everything else: 1997 BMW M3 |
![]() |
![]() |
![]() |
#7 |
Garage Queen Material
Join Date: Oct 2002
Location: USA
Posts: 4,129
|
only thing i worried about with them was performancel i dont want problems since i'm making a little bit of power
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,963
|
Wheel spacers are just that.... they space the wheel out & decrease the amount of useable thread required to hold the wheel or require a longer stud to retain the required amount of stud thread. Longer studs decrease the strength of the stud.
Adapters actually bolt to the hub like any aluminum wheel & in turn have their own studs that your wheel bolts to. The end result is the same as a wider rear end housing. Minimum width is 1" & they can be built for up to 4" increase in track width. Wheel spacers are typically cast aluminum (weak) or steel. Wheel adapters are typically made of billet aluminum which is as strong as cast steel but lighter.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
![]() |
![]() |
![]() |
Bookmarks |
|
|