WTB: Alt Bracket for Head w/o holes - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Piper71c10 · 01-10-2005, 01:38 AM

Got a set of double hump heads w/o acc bolt holes, and looking for a alt bracket setup that would work with these. Anyone?

Piper

muddyole 69 · 01-10-2005, 03:47 AM

Any reputable rod shop should have the aftermarket stuff got mine thru Jegs Mail order a few years back and was around 50 to the door check with them online @ Jegs.com goodluck Mike

MOTHERTRUCKERS · 01-10-2005, 05:21 AM

30.00 including shipping, they are cleaned up ready to paint off a 67 327 with lower block mount,spacer and top adjuster arm.

67ChevyC10Stepside · 01-10-2005, 12:48 PM

the two i have had.......were the arm that went from the water pump to a header stud....and then the one off my dad's 86 goes from the water pump to the intake....why wont those work?

MOTHERTRUCKERS · 01-10-2005, 09:15 PM

If you have a short water pump the 73 and newer brackets are for a long water pump 72 and eariler were short pumps.

Piper71c10 · 01-10-2005, 09:39 PM

MotherTruckers-
I'll take you up. PM me your address and I'll mail you a check.

Piper

**southern parts** · 01-10-2005, 10:34 PM

does your truck have the right exhaust manifold for the early type alt brackets?

67ChevyC10Stepside · 01-10-2005, 11:21 PM

oh....i never knew the difference.....was just trieing to help

Piper71c10 · 01-10-2005, 11:47 PM

What is the correct manifold for the alt brackets? This isn't for me, it's for a pal that put a cheap ass set of new heads onto a box van that he want's to dump. It's like an 82 gmc 1 ton, so I'm now not sure what will work.......

Piper

MOTHERTRUCKERS · 01-11-2005, 02:28 AM

There is also early alt and generator brackets that bolt to the front of the driver side ramhorn exhaust and some later that bolt to the side. I also have these and the driver ramhorn if interested.

MOTHERTRUCKERS · 01-11-2005, 08:33 PM

piper71c10 I sent you a pm almost all my alt and generator brackets are either stolen or the scrap guy got them by mistake, if you have sent the check i will try to get some more this week if not i'll still try to get them for you. I have lots of guys that owe me favors aroud here.

Piper71c10 · 01-16-2005, 04:14 PM

Revisiting this a little bit, Still looking for a bracket, but I want one to mount the Alt on the passenger side. Anything like that out there?

Piper
Trying to help a buddy out who is getting pretty desperate...

Piper71c10 · 01-18-2005, 11:14 AM

ttt

Hotrodhenryj · 01-18-2005, 11:53 AM

Here is a pic of the brackets and also how they mount. You will need to have the exhaust manifold that matches this setup. 25 shipped. Chuck

67ChevyC10Stepside · 01-18-2005, 03:33 PM

change your water pump and use this style setup....

67ChevyC10Stepside · 01-18-2005, 03:35 PM

i have an extra setup like this if this is what you want to do. water pumps are extremely cheap and i personally have like 6 extras lol so it wouldnt be hard to do.

Piper71c10 · 01-19-2005, 05:24 PM

67c10--- that doesn't bolt to the head anywhere?

if not, I'll take one, how much shipped to 98382?

piper

67ChevyC10Stepside · 01-19-2005, 09:59 PM

look at the second pic up....bottom bracket bolts to the water pump bolts..the top one bolts to water pump and intake....hell i dont know what to charge for them lol

Vince Putt · 01-19-2005, 10:39 PM

The pictures posted the lower bolt goes through the bracket then alternator then through a spacer to a head bolt hole. Look under the alternator you'll see the spacer.

67ChevyC10Stepside · 01-19-2005, 10:41 PM

awww chit you're right..that's the only head bolt the setup uses..

Piper71c10 · 01-20-2005, 12:23 AM

I see... anyone ever flip one like HoTRodHenryJ has to use on the passenger side?
I'm dead set on mounting this thing on the pass side, and would like to find one sooon!

Piper

01-10-2005, 01:38 AM	#1
Piper71c10 Unending Project Join Date: Aug 2003 Location: Sequim, WA Posts: 337	WTB: Alt Bracket for Head w/o holes Got a set of double hump heads w/o acc bolt holes, and looking for a alt bracket setup that would work with these. Anyone? Piper

01-10-2005, 03:47 AM	#2
muddyole 69 Senior Member Join Date: Jan 2004 Location: SE Ohio Posts: 1,121	alt set up Any reputable rod shop should have the aftermarket stuff got mine thru Jegs Mail order a few years back and was around 50 to the door check with them online @ Jegs.com goodluck Mike __________________ hav'n fun be'n me

01-10-2005, 05:21 AM	#3
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	30.00 including shipping, they are cleaned up ready to paint off a 67 327 with lower block mount,spacer and top adjuster arm. __________________ Rest in Peace Ed. Thanks for all the good times.

01-10-2005, 12:48 PM	#4
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	the two i have had.......were the arm that went from the water pump to a header stud....and then the one off my dad's 86 goes from the water pump to the intake....why wont those work? __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-10-2005, 09:15 PM	#5
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	If you have a short water pump the 73 and newer brackets are for a long water pump 72 and eariler were short pumps. __________________ Rest in Peace Ed. Thanks for all the good times.

01-10-2005, 09:39 PM	#6
Piper71c10 Unending Project Join Date: Aug 2003 Location: Sequim, WA Posts: 337	MotherTruckers- I'll take you up. PM me your address and I'll mail you a check. Piper

01-10-2005, 10:34 PM	#7
southern parts Senior Member Join Date: Apr 2003 Location: Elberton Ga. Posts: 3,470	does your truck have the right exhaust manifold for the early type alt brackets?

01-10-2005, 11:21 PM	#8
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	oh....i never knew the difference.....was just trieing to help __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-10-2005, 11:47 PM	#9
Piper71c10 Unending Project Join Date: Aug 2003 Location: Sequim, WA Posts: 337	What is the correct manifold for the alt brackets? This isn't for me, it's for a pal that put a cheap ass set of new heads onto a box van that he want's to dump. It's like an 82 gmc 1 ton, so I'm now not sure what will work....... Piper

01-11-2005, 02:28 AM	#10
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	There is also early alt and generator brackets that bolt to the front of the driver side ramhorn exhaust and some later that bolt to the side. I also have these and the driver ramhorn if interested. __________________ Rest in Peace Ed. Thanks for all the good times.

01-11-2005, 08:33 PM	#11
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	piper71c10 I sent you a pm almost all my alt and generator brackets are either stolen or the scrap guy got them by mistake, if you have sent the check i will try to get some more this week if not i'll still try to get them for you. I have lots of guys that owe me favors aroud here. __________________ Rest in Peace Ed. Thanks for all the good times.

01-16-2005, 04:14 PM	#12
Piper71c10 Unending Project Join Date: Aug 2003 Location: Sequim, WA Posts: 337	Revisiting this a little bit, Still looking for a bracket, but I want one to mount the Alt on the passenger side. Anything like that out there? Piper Trying to help a buddy out who is getting pretty desperate...

01-18-2005, 11:14 AM	#13
Piper71c10 Unending Project Join Date: Aug 2003 Location: Sequim, WA Posts: 337	ttt

01-18-2005, 11:53 AM	#14
Hotrodhenryj Truck Farmer Join Date: Nov 2001 Location: Lake Havasu City, Arizona Posts: 1,192	Brackets Here is a pic of the brackets and also how they mount. You will need to have the exhaust manifold that matches this setup. 25 shipped. Chuck Attached Images __________________ Arizona rust free sheetmetal

01-18-2005, 03:33 PM	#15
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	change your water pump and use this style setup.... Attached Images __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.



Register or Log In To remove these advertisements.

01-18-2005, 03:35 PM	#16
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	i have an extra setup like this if this is what you want to do. water pumps are extremely cheap and i personally have like 6 extras lol so it wouldnt be hard to do. Attached Images __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-19-2005, 05:24 PM	#17
Piper71c10 Unending Project Join Date: Aug 2003 Location: Sequim, WA Posts: 337	67c10--- that doesn't bolt to the head anywhere? if not, I'll take one, how much shipped to 98382? piper

01-19-2005, 09:59 PM	#18
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	look at the second pic up....bottom bracket bolts to the water pump bolts..the top one bolts to water pump and intake....hell i dont know what to charge for them lol __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-19-2005, 10:39 PM	#19
Vince Putt Hippy Join Date: Sep 2004 Location: kaska, pa Posts: 95	The pictures posted the lower bolt goes through the bracket then alternator then through a spacer to a head bolt hole. Look under the alternator you'll see the spacer.

01-19-2005, 10:41 PM	#20
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	awww chit you're right..that's the only head bolt the setup uses.. __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-20-2005, 12:23 AM	#21
Piper71c10 Unending Project Join Date: Aug 2003 Location: Sequim, WA Posts: 337	I see... anyone ever flip one like HoTRodHenryJ has to use on the passenger side? I'm dead set on mounting this thing on the pass side, and would like to find one sooon! Piper

Register or Log In To remove these advertisements.