front lower bumpstop install? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chevybill · 01-16-2005, 10:50 PM

I am in the midle of my front suspension rebuild and need some tips on installing the lower rubber triangle shaped bumpstops.

Is there a trick or any helpful hints are greatly appreciated.

Tx Firefighter · 01-16-2005, 11:00 PM

Put them in the microwave for about 10-15 seconds then run outside and pop them in. The heat makes them pliable.

SCOTI · 01-16-2005, 11:47 PM

I tried the microwave thing & it didn't work for me. I tried boiling water as well w/no luck.

What I wound up doing was drill an access hole (I had a 5/8" hole-saw handy)in the front of the bump-stop 'mount' so that I could grab the rubber & help pull it into place while pushing/wedging it in from on top. I also used a little dish washing soap to make things a little slippery. It took longer to drill the hole than pull the snubber into place (& it didn't take long to drill the hole).

chevybill · 01-17-2005, 12:35 PM

thanks for the replies

ChevyDude · 01-17-2005, 01:03 PM

Dish soap and alot of wiggling and forcing them into to slot.

67chev · 01-17-2005, 03:23 PM

I sprayed mine down with silicone, popped one side in, then used a flat prybar (could use a big screwdriver) and pushed the other side down into the channel. Good luck however you try to do it!!

Vince M · 01-17-2005, 08:36 PM

I just did mine this week. I got some liquid laundry soap...gooped a bit on the triagle shape and pushed it straight down. Went in real easy. Mine were brand new so they were already pliable. My lower A-arms are also powder coated so that might have helped. They are real shinny and slick.

4x4Poet · 01-17-2005, 11:28 PM

If you already have the silicone (tube or spray), it would be a little better since it's not water based, is harmless to rubber, and is more slippery.

01-16-2005, 10:50 PM	#1
chevybill Senior Member Join Date: Oct 2004 Location: calhoun city ms Posts: 940	front lower bumpstop install? I am in the midle of my front suspension rebuild and need some tips on installing the lower rubber triangle shaped bumpstops. Is there a trick or any helpful hints are greatly appreciated. __________________ ongoing 1970 c 10 lwb 1994 z-28 few mods.-owned since new 1978 vette silver/grey 25th anniv. paint

01-16-2005, 11:00 PM	#2
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Put them in the microwave for about 10-15 seconds then run outside and pop them in. The heat makes them pliable. __________________ I'm on the Instagram- @Gearhead_Kevin

01-16-2005, 11:47 PM	#3
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,947	I tried the microwave thing & it didn't work for me. I tried boiling water as well w/no luck. What I wound up doing was drill an access hole (I had a 5/8" hole-saw handy)in the front of the bump-stop 'mount' so that I could grab the rubber & help pull it into place while pushing/wedging it in from on top. I also used a little dish washing soap to make things a little slippery. It took longer to drill the hole than pull the snubber into place (& it didn't take long to drill the hole). __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

01-17-2005, 12:35 PM	#4
chevybill Senior Member Join Date: Oct 2004 Location: calhoun city ms Posts: 940	thanks for the replies __________________ ongoing 1970 c 10 lwb 1994 z-28 few mods.-owned since new 1978 vette silver/grey 25th anniv. paint

01-17-2005, 01:03 PM	#5
ChevyDude Senior Member Join Date: Jun 2003 Location: Westminster, CO Posts: 3,071	Dish soap and alot of wiggling and forcing them into to slot. __________________ Alex 1971 Lil' Red 350 SBC 700R4

01-17-2005, 03:23 PM	#6
67chev Registered User Join Date: Apr 2004 Location: Spokane, WA Posts: 458	I sprayed mine down with silicone, popped one side in, then used a flat prybar (could use a big screwdriver) and pushed the other side down into the channel. Good luck however you try to do it!! __________________ "SicStee8" Chevy SWB Fleetside, in progress...500 HP 383 w/TriPower, 700r4, 3.73's, Lowered, Shaved Driprail/sidemarkers/handles/ant, Gonna rock!! '96 Chevy Tahoe 4X4 '84 Chevy C/K10 4X4 (FOR SALE)

01-17-2005, 08:36 PM	#7
Vince M Senior Member Join Date: Apr 2000 Location: Orlando, FL Posts: 1,076	I just did mine this week. I got some liquid laundry soap...gooped a bit on the triagle shape and pushed it straight down. Went in real easy. Mine were brand new so they were already pliable. My lower A-arms are also powder coated so that might have helped. They are real shinny and slick. __________________ ............................................................ 68 Chevy CST SWB w/LS1, carb & 700r4. Golden Anniversary clone with a few improvements.

01-17-2005, 11:28 PM	#8
4x4Poet Registered User Join Date: Nov 2004 Location: "Under Montana skies." Posts: 1,836	If you already have the silicone (tube or spray), it would be a little better since it's not water based, is harmless to rubber, and is more slippery. __________________ '71 GMC K20 Suburban, '71 GMC K10 Suburban, '72 Chevy C10 CST Suburban, '72 Chevy K20 clunker pickup.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.