Jack location - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Gary 70 Jimmy** · 04-21-2005, 09:26 AM

I no some one was asking about the jack location I just got done putting mine in. There were 2 screw holes in the back floor to screw the spring bracket to the floor just make sure you dont use screws that are to long because they will hit the plate the holds the back seat in and will strip out the holes and then you will have to drill new holes like me.

**Gary 70 Jimmy** · 04-21-2005, 09:28 AM

pcs

71jimmy · 04-21-2005, 12:20 PM

Looks nice and clean. Is the jack same as on the trucks? Can you post a closeup pic of the jack spring plate, without the jack strapped in it?

**Gary 70 Jimmy** · 04-21-2005, 12:49 PM

I will take a picture this week end

LUV2XCLR8 · 04-21-2005, 03:12 PM

Quote:

Originally Posted by 71jimmy

Can you post a closeup pic of the jack spring plate

This thing

71jimmy · 04-21-2005, 06:23 PM

Gotcha LUV, is that the extra one your going to sell me? LOL

By the way, are the jacks and lug wrench etc the same as on the trucks?

LUV2XCLR8 · 04-21-2005, 06:46 PM

Quote:

Originally Posted by 71jimmy

Gotcha LUV, is that the extra one your going to sell me? LOL

SORRY, NO

Quote:

Originally Posted by 71jimmy

By the way, are the jacks and lug wrench etc the same as on the trucks?

ASKED SEVERAL PEEPS THE SAME QUESTION LAST WEEK AT
THE MEMPHIS SUPER CHEVY SHOW, NOBODY KNEW IF A 4WD
WAS ANY DIFFERENT SO I BOUGHT SAME STUFF AS ABOVE.

(JACK & FOLDING CRANK HANDLE, HAD A TIRE IRON ALREADY)

Huck · 04-21-2005, 06:57 PM

Need one of them jack spring holder thingies. Got the jack handle holder stuff---also need an original tire iron~~~. Always something!

**pound41** · 04-21-2005, 07:31 PM

Hey Huck I PM you about the 70 blazer that had the sticker on the wheelwell with jack instructions did you get it.

Huck · 04-22-2005, 07:57 AM

pound, the e-bay number you game me did not get me to a blazer but some part to something. I have seen several very original blazers come up on e-bay so that may be the best source for a copy of an original blazer jacking instruction sheet. There seems to have been two instruction sheets--one would be glued on each rear wheel well. Will find one eventually. But now I also get to look for that little jack holder----and what are those two brackets in the picture just to the right???????????????

**Gary 70 Jimmy** · 04-22-2005, 08:33 AM

The black one in Luv picture is the one that I have in my jimmy I will take a picture later.

**pound41** · 04-22-2005, 08:45 AM

Sorry HUCK I blew that one. Must of hit a wrong key. It was a gold 70 blazer original or 2nd owner knew the history of truck. Anyway they had a pic of back cargo area and there it was on the wheel well would have been a good source.

04-21-2005, 09:26 AM	#1
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,402	Jack location I no some one was asking about the jack location I just got done putting mine in. There were 2 screw holes in the back floor to screw the spring bracket to the floor just make sure you dont use screws that are to long because they will hit the plate the holds the back seat in and will strip out the holes and then you will have to drill new holes like me.

04-21-2005, 09:28 AM	#2
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,402	pcs Attached Images

04-21-2005, 12:20 PM	#3
71jimmy Registered User Join Date: Mar 2004 Location: Sacramento, CA Posts: 1,084	Looks nice and clean. Is the jack same as on the trucks? Can you post a closeup pic of the jack spring plate, without the jack strapped in it? __________________ '71 Jimmy, 350, SM465, NP205, 2in Tuff Country lift, 33s on rallies, TBI, softtop and hardtop "If life was fair you'd be able to afford one of each and a garage large enough to house them all." Last edited by 71jimmy; 04-21-2005 at 12:21 PM.

04-21-2005, 06:23 PM	#6
71jimmy Registered User Join Date: Mar 2004 Location: Sacramento, CA Posts: 1,084	Gotcha LUV, is that the extra one your going to sell me? LOL By the way, are the jacks and lug wrench etc the same as on the trucks? __________________ '71 Jimmy, 350, SM465, NP205, 2in Tuff Country lift, 33s on rallies, TBI, softtop and hardtop "If life was fair you'd be able to afford one of each and a garage large enough to house them all."

04-21-2005, 12:49 PM	#4
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,402	I will take a picture this week end

04-21-2005, 06:57 PM	#8
Huck Senior Member Join Date: Jun 2001 Location: Shelbyville, KY Posts: 3,269	Need one of them jack spring holder thingies. Got the jack handle holder stuff---also need an original tire iron~~~. Always something!

04-21-2005, 07:31 PM	#9
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,268	Hey Huck I PM you about the 70 blazer that had the sticker on the wheelwell with jack instructions did you get it.

04-22-2005, 07:57 AM	#10
Huck Senior Member Join Date: Jun 2001 Location: Shelbyville, KY Posts: 3,269	pound, the e-bay number you game me did not get me to a blazer but some part to something. I have seen several very original blazers come up on e-bay so that may be the best source for a copy of an original blazer jacking instruction sheet. There seems to have been two instruction sheets--one would be glued on each rear wheel well. Will find one eventually. But now I also get to look for that little jack holder----and what are those two brackets in the picture just to the right???????????????

04-22-2005, 08:33 AM	#11
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,402	The black one in Luv picture is the one that I have in my jimmy I will take a picture later.

04-22-2005, 08:45 AM	#12
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,268	Sorry HUCK I blew that one. Must of hit a wrong key. It was a gold 70 blazer original or 2nd owner knew the history of truck. Anyway they had a pic of back cargo area and there it was on the wheel well would have been a good source.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.