![]() |
![]() |
#1 |
Registered User
Join Date: Aug 2005
Location: Canton SD
Posts: 7
|
Temp Gauge Troubles
When I take the wire off the sending unit and ground it out, the needle moves 3/4 of the way across the gauge.
(I think this would indicate that the gauge is OK?) I also put in a new temp sensor between the #1 & #3 spark plug. I did not use teflon tape as not to interfere with the ground. Still the needle only jumps when I turn the key on and nothing after that. Any other Ideas that could cause my temp gauge not to work? |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jan 2000
Location: Wyoming USA
Posts: 2,445
|
Has that wire to the sender been burnt and spliced before?May need to run a new wire.
__________________
2001 Silverado K-1500 2005 FXDWG stage3 69 CHEVY Short/Step 327/4L60 373 posi 63 IMPALA 327 |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Aug 2005
Location: Canton SD
Posts: 7
|
Spliced Wire
The wire was broken so I spliced in a new one, I used a much heaver gauge wire however, could going from original size to large size back down to original size be my problem?
|
![]() |
![]() |
![]() |
#4 |
II Timothy 4:2
Join Date: Mar 2005
Location: Fort Worth
Posts: 361
|
I have a question about the gauge. If you are looking at the back of the gauge, which post is the 12v and which one is the sender?
__________________
72 C-20 2WD LWB Custom Camper Deluxe 350 4 Speed "Project Lazarus" MY TRUE PRIDE AND JOY "Dangit, Bobby, people will see that oil stain and think I'm a drunk." |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Aug 2005
Location: Canton SD
Posts: 7
|
With the key off, both posts are dead.
With the key on, both posts are hot?...could it be my circuit board? |
![]() |
![]() |
![]() |
#6 |
State of Confusion!
![]() ![]() Join Date: Jul 2002
Location: Gulfport, MS USA
Posts: 46,924
|
another thing that it might be is they gave you the sensor for an idiot light dash instead of the gauge model. They do make a difference.
__________________
Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God! |
![]() |
![]() |
![]() |
#7 |
member #16
![]() Join Date: Dec 1999
Location: Yuba City Ca.
Posts: 3,618
|
[QUOTE=RJ Swanson]When I take the wire off the sending unit and ground it out, the needle moves 3/4 of the way across the gauge.
(I think this would indicate that the gauge is OK?) Actually the guage should peg on the hot side. I would check further into sender wire. Possible bad ga. also. Plus check sender # as was mentioned. John
__________________
john http://67-72chevytrucks.com/vboard/showgroups.php board vendors ![]() http://www.flickr.com/photos/1745471...7602865984234/ |
![]() |
![]() |
![]() |
#8 | |
II Timothy 4:2
Join Date: Mar 2005
Location: Fort Worth
Posts: 361
|
Quote:
Anybody?
__________________
72 C-20 2WD LWB Custom Camper Deluxe 350 4 Speed "Project Lazarus" MY TRUE PRIDE AND JOY "Dangit, Bobby, people will see that oil stain and think I'm a drunk." |
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Aug 2005
Location: Canton SD
Posts: 7
|
Possible Cause
I did a little more research...
I bought the sensor at NAPA they have the same part number for the light and the gauge sensor. I called a few other parts stores and they have two different part numbers and prices for the two sensors I guess sometimes even the experts can be wrong |
![]() |
![]() |
![]() |
Bookmarks |
|
|