PRogress on the Engine rebuild.... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Zumo · 01-21-2006, 11:08 PM

Well, slowly but surely, I am replacing my old broke motor (see pic) with a reman. I bought. I really don't have the money right now for a full resto so I am just trying to clean up a few things for my new(rebuilt) motor install. Once I get the motor painted and asembled, it will be the cleaned part of the whole truck. I figure I'll just do a piece at a time.

Anyway since I have the engine out I decided to clean up the oil and muddy mess left behind by the old motor. I can't really get to all areas with out totaly disassembling the front in so I am doing what I can for now. Should I repaint it or put some sort of coating? What about the areas I can't get the grease out? One of many dilemas.

What I am doing is removing and painting the fender wells. I also decided to rattle can the outside of the truck with a Krylon satin paint. I am using it insted of primer. Seems to work ok and it's not glossy at all.

Oh also check out the last pic. It's my tranny with a pretective shield of mud and dirt. Going to clean that up and replace the filter.

matthufham · 01-21-2006, 11:25 PM

gotta hate bad bearings. good luck to ya!

70c10swb · 01-22-2006, 12:18 AM

Quote:

Originally Posted by matthufham

gotta hate bad bearings. good luck to ya!

what bearing?

bojoe · 01-22-2006, 12:37 AM

That sucks. Time to build some horsepwer.

SCOTI · 01-22-2006, 12:58 AM

Looks good Zumo. Keep @ it.
I like the satin touch to the fender.

**tnblazerk5** · 01-22-2006, 01:03 AM

big ouch on the bearing

the fender looks good though

Striker169 · 01-22-2006, 02:33 AM

wow that trans was covered!

LUV2XCLR8 · 01-22-2006, 07:32 AM

Sheeesh, I agree with the others, what bearing

Zumo · 01-22-2006, 10:27 AM

Yeah that bearing cuased a whole mess of trouble. My engine crapped out whil I was on the highway. It broke one of the brass keepers on the top of one of the valves which jacked up the valve area and even broke off some of the metal on the head around the valve.

The block may still be good but I am not sure. I went ahead and bought a remanufatured 74 (I believe) 350 4 bolt main with flat top pistons. The old engin was a punched out stock 307.

As for the trans, I think this truck spent some time around the Red River area in Oklahoma be fore I got it. All the dirt I have been cleaning off the engine bay has been red.

PanelDeland · 01-22-2006, 11:55 AM

I would soak the whole thing with degreaser and go watch Horsepower.Then rinse and resoak.Leave it over night and do it again.I like paint to dress up the engine compartment.If you can tow it to the car wash or have a power washer it will come a lot cleaner.Hope you don't got ice.A wire brush and scraper first will make things go quicker.

Tx Firefighter · 01-22-2006, 12:08 PM

Plug the yoke hole and cooler line ports and use Easy-Off oven cleaner and the local car wash.

Go at night though, the car wash owners will crap a golden kitty if they catch you there doing that.

lloyd k · 01-22-2006, 12:58 PM

use a putty knife and i agree take the whole truck to a power wash, worth the effort, its funny the the comments you hear when you take a jack and jack stands with ya

NO LONGER DISTURBED KONCEPTZ · 01-22-2006, 01:01 PM

Man Im about to have to do the same thing with my 84 and I cant afford it right now. It sucks.

Zumo · 01-22-2006, 10:40 PM

My new neighbor 2 doors down has a pressure washer, I should take him some beer and see if he'll let me borrow it.

NO LONGER DISTURBED KONCEPTZ · 01-22-2006, 11:30 PM

Quote:

Originally Posted by Zumo

My new neighbor 2 doors down has a pressure washer, I should take him some beer and see if he'll let me borrow it.

Sound like a good plan. "I love it when a plan comes together" Hanabal A-Team

edmonton72 · 01-23-2006, 01:00 AM

That sucks about your motor dude. My tranny looked like that too. I used a putty knife and a wire brush, and that got most of the crap off. Then I would use ur neighbor's pressure washer to get rid of the rest of the dirt and grease.

stllookn · 01-23-2006, 03:01 AM

Just a thought but I would service the tranny while you have it out and replace both of the shaft seals on the tranny. I forgot to do mine and one of them is leaking...bummer after you have the engine back into place. The shaft seals are so easy to do when the tranny is sitting in the bed of the truck.

Zumo · 01-23-2006, 09:42 AM

Quote:

Originally Posted by stllookn

Just a thought but I would service the tranny while you have it out and replace both of the shaft seals on the tranny. I forgot to do mine and one of them is leaking...bummer after you have the engine back into place. The shaft seals are so easy to do when the tranny is sitting in the bed of the truck.

I was thinking about that. I am in no hurry to get it back in, hell the truck has been sitting for 2 years since it broke down.

67ChevyRedneck · 01-23-2006, 11:20 AM

Quote:

Originally Posted by Zumo

My new neighbor 2 doors down has a pressure washer, I should take him some beer and see if he'll let me borrow it.

That first pic looks WAY too familiar. I bought a reman as well (autozone). $800 bucks was a lot cheaper than the GM blocks for $1600. (would of loved to have one, but a budget is a budget). My uncle was kind enough to pressure wash mine. I then used a drill to wire brush the frame. A coat of spray can primer and black paint. I went a little more in depth though. When I had the motor out I tore the entire suspension apart. Clean, sanded, primed and painted everything, added power disks, and bought all new suspension components (ball joints, tie rods etc...) Good luck gettin 'er all back together.

Zumo · 01-23-2006, 11:58 AM

I am seriously thinking about doing that to the suspension. It is also full of mud and grease. Seem so easy since it's all tore down. I did remove the fender wells and am planning on repainting those as well.

01-21-2006, 11:08 PM	#1
Zumo Hot Rods For Life Join Date: Sep 2001 Location: Waxahachie, TX Posts: 3,305	PRogress on the Engine rebuild.... Well, slowly but surely, I am replacing my old broke motor (see pic) with a reman. I bought. I really don't have the money right now for a full resto so I am just trying to clean up a few things for my new(rebuilt) motor install. Once I get the motor painted and asembled, it will be the cleaned part of the whole truck. I figure I'll just do a piece at a time. Anyway since I have the engine out I decided to clean up the oil and muddy mess left behind by the old motor. I can't really get to all areas with out totaly disassembling the front in so I am doing what I can for now. Should I repaint it or put some sort of coating? What about the areas I can't get the grease out? One of many dilemas. What I am doing is removing and painting the fender wells. I also decided to rattle can the outside of the truck with a Krylon satin paint. I am using it insted of primer. Seems to work ok and it's not glossy at all. Oh also check out the last pic. It's my tranny with a pretective shield of mud and dirt. Going to clean that up and replace the filter. Attached Images __________________ 1968 C10 LWB **SOLD* Andy Viva Los Bicicletas! Los Muertos Custom Bicycles

01-21-2006, 11:25 PM	#2
matthufham Registered User Join Date: Feb 2005 Location: Carl Junction, Missouri Posts: 2,061	Re: PRogress on the Engine rebuild.... gotta hate bad bearings. good luck to ya!

01-22-2006, 12:37 AM	#4
bojoe Registered User Join Date: Dec 2005 Location: Benton, IL Posts: 95	Re: PRogress on the Engine rebuild.... That sucks. Time to build some horsepwer. __________________ 1985 GMC 1/2 ton 305/700R4 1975 Chevrolet 1/2 ton 350/350 1971 Chevrolet C-60 427/5+2 1981 Cadillac Deville 6.0/368cid 2003 Chevrolet Suburban(wife's ride) 2007 Peterbilt 379/How I make money More old John Deere tractors than I know what to do with.

01-22-2006, 12:58 AM	#5
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	Re: PRogress on the Engine rebuild.... Looks good Zumo. Keep @ it. I like the satin touch to the fender. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

01-22-2006, 01:03 AM	#6
tnblazerk5 User #12137 Join Date: Apr 2004 Location: kingsport,upper east tenn Posts: 11,598	Re: PRogress on the Engine rebuild.... big ouch on the bearing the fender looks good though

01-22-2006, 02:33 AM	#7
Striker169 Car O'Holic Join Date: Jan 2005 Location: Austin, Tx. Posts: 692	Re: PRogress on the Engine rebuild.... wow that trans was covered!

01-22-2006, 07:32 AM	#8
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	Re: PRogress on the Engine rebuild.... Sheeesh, I agree with the others, what bearing __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

01-22-2006, 10:27 AM	#9
Zumo Hot Rods For Life Join Date: Sep 2001 Location: Waxahachie, TX Posts: 3,305	Re: PRogress on the Engine rebuild.... Yeah that bearing cuased a whole mess of trouble. My engine crapped out whil I was on the highway. It broke one of the brass keepers on the top of one of the valves which jacked up the valve area and even broke off some of the metal on the head around the valve. The block may still be good but I am not sure. I went ahead and bought a remanufatured 74 (I believe) 350 4 bolt main with flat top pistons. The old engin was a punched out stock 307. As for the trans, I think this truck spent some time around the Red River area in Oklahoma be fore I got it. All the dirt I have been cleaning off the engine bay has been red. __________________ 1968 C10 LWB **SOLD* Andy Viva Los Bicicletas! Los Muertos Custom Bicycles

01-22-2006, 11:55 AM	#10
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,992	Re: PRogress on the Engine rebuild.... I would soak the whole thing with degreaser and go watch Horsepower.Then rinse and resoak.Leave it over night and do it again.I like paint to dress up the engine compartment.If you can tow it to the car wash or have a power washer it will come a lot cleaner.Hope you don't got ice.A wire brush and scraper first will make things go quicker. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" Last edited by PanelDeland; 01-22-2006 at 11:56 AM.

01-22-2006, 12:08 PM	#11
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: PRogress on the Engine rebuild.... Plug the yoke hole and cooler line ports and use Easy-Off oven cleaner and the local car wash. Go at night though, the car wash owners will crap a golden kitty if they catch you there doing that. __________________ I'm on the Instagram- @Gearhead_Kevin

01-22-2006, 12:58 PM	#12
lloyd k Registered User Join Date: Feb 2004 Location: columbus,ohio Posts: 201	Re: PRogress on the Engine rebuild.... use a putty knife and i agree take the whole truck to a power wash, worth the effort, its funny the the comments you hear when you take a jack and jack stands with ya __________________ 67 swb gmc,big block cadillac powered,400 turbo,2.73 ratio and disc brakes-basically a frankenstein of many parts-

01-22-2006, 01:01 PM	#13
NO LONGER DISTURBED KONCEPTZ Registered User Join Date: Aug 2004 Posts: 257	Re: PRogress on the Engine rebuild.... Man Im about to have to do the same thing with my 84 and I cant afford it right now. It sucks.

01-22-2006, 10:40 PM	#14
Zumo Hot Rods For Life Join Date: Sep 2001 Location: Waxahachie, TX Posts: 3,305	Re: PRogress on the Engine rebuild.... My new neighbor 2 doors down has a pressure washer, I should take him some beer and see if he'll let me borrow it. __________________ 1968 C10 LWB **SOLD* Andy Viva Los Bicicletas! Los Muertos Custom Bicycles

01-23-2006, 01:00 AM	#16
edmonton72 Nothings as cool as my 72 Join Date: May 2005 Location: Edmonton, AB, Kanuckastan Posts: 181	Re: PRogress on the Engine rebuild.... That sucks about your motor dude. My tranny looked like that too. I used a putty knife and a wire brush, and that got most of the crap off. Then I would use ur neighbor's pressure washer to get rid of the rest of the dirt and grease. __________________ 1972 C10 Longbox In the middle of body off restoration Rebuilt 355, turbo 400, 3.42 12-bolt Rolling chassis finally done and cab mounted. Now onto sanding, bondo and more sanding.

01-23-2006, 03:01 AM	#17
stllookn Saving 1 truck at a time! Join Date: Aug 2001 Location: Kent, WA Posts: 6,465	Re: PRogress on the Engine rebuild.... Just a thought but I would service the tranny while you have it out and replace both of the shaft seals on the tranny. I forgot to do mine and one of them is leaking...bummer after you have the engine back into place. The shaft seals are so easy to do when the tranny is sitting in the bed of the truck. __________________ '68 C20 Longhorn 50th Anniversary 400/TH400 '68 C20 Longhorn 50th Anniversary 468/TH400w/buckets '72 C20 Halfhorn (Longhorn w/o cab and front clip) '69 Flxible Cruiser (look up ugly in the dictionary)



Register or Log In To remove these advertisements.

01-23-2006, 11:58 AM	#20
Zumo Hot Rods For Life Join Date: Sep 2001 Location: Waxahachie, TX Posts: 3,305	Re: PRogress on the Engine rebuild.... I am seriously thinking about doing that to the suspension. It is also full of mud and grease. Seem so easy since it's all tore down. I did remove the fender wells and am planning on repainting those as well. __________________ 1968 C10 LWB **SOLD* Andy Viva Los Bicicletas! Los Muertos Custom Bicycles

Register or Log In To remove these advertisements.