Belt Drive System - The 1947 - Present Chevrolet & GMC Truck Message Board Network

72ChevyCheyenne · 10-08-2002, 07:03 AM

I need a advice on putting together the correct pulleys and brackets for a ZZ502 crate engine. I need the alternator bracket, power steering pump bracket and shaft pulley. Any suggestions?

Church · 10-08-2002, 07:12 AM

I can get you the March Performance Big Block setup.

72ChevyCheyenne · 10-08-2002, 07:23 AM

How much?

Church · 10-08-2002, 07:49 AM

This is kit #23020. It drives the water pump, alt, and p.s. w/ a keyway type pulley. It runs 486.00 w/ shipping.

sam's 72 · 10-08-2002, 02:53 PM

I was looking through one of my web sites and just happened to come across this, it might help you. Once you get on the site just scroll down, you will see a picture of a guy setting up a 502 with pulleys. I hope it helps some. http://hotrodgossip.com/
Sam

10-08-2002, 07:03 AM	#1
72ChevyCheyenne Registered User Join Date: May 2002 Location: Woodstock, GA USA Posts: 300	Belt Drive System I need a advice on putting together the correct pulleys and brackets for a ZZ502 crate engine. I need the alternator bracket, power steering pump bracket and shaft pulley. Any suggestions? __________________ Bill Durham http://home.attbi.com/~bulldurham 72 Cheyenne Restoration in progress Currently: frame sand blasted and powdercoated, Inline Tube brake and fuel lines, Blazer tank in rear, Holley Red electronic fuel pump, Eaton posi with 3.42 gears, 2 1/2" drop front spindles, 4" drop rear springs with adjustable panhard bar, KYB shocks, ZZ 502/502 GM Performance crate engine, Zoops brackets and pulleys, Vintage Air, dual electric fans, Ram Air II hood and late model sport side bed.

10-08-2002, 07:23 AM	#3
72ChevyCheyenne Registered User Join Date: May 2002 Location: Woodstock, GA USA Posts: 300	How much? __________________ Bill Durham http://home.attbi.com/~bulldurham 72 Cheyenne Restoration in progress Currently: frame sand blasted and powdercoated, Inline Tube brake and fuel lines, Blazer tank in rear, Holley Red electronic fuel pump, Eaton posi with 3.42 gears, 2 1/2" drop front spindles, 4" drop rear springs with adjustable panhard bar, KYB shocks, ZZ 502/502 GM Performance crate engine, Zoops brackets and pulleys, Vintage Air, dual electric fans, Ram Air II hood and late model sport side bed.

10-08-2002, 07:49 AM	#4
Church Carolina Classic Trucks Join Date: Jan 2000 Location: The South Posts: 792	This is kit #23020. It drives the water pump, alt, and p.s. w/ a keyway type pulley. It runs 486.00 w/ shipping. __________________

10-08-2002, 02:53 PM	#5
sam's 72 Senior Member Join Date: Nov 2001 Location: Pasadena, Texas, USA Posts: 1,005	I was looking through one of my web sites and just happened to come across this, it might help you. Once you get on the site just scroll down, you will see a picture of a guy setting up a 502 with pulleys. I hope it helps some. http://hotrodgossip.com/ Sam __________________ 72 LWB chevy truck. Pasadena, Texas

10-08-2002, 07:12 AM	#2
Church Carolina Classic Trucks Join Date: Jan 2000 Location: The South Posts: 792	I can get you the March Performance Big Block setup. __________________ Last edited by Church; 10-08-2002 at 07:14 AM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.