|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
06-11-2006, 09:09 PM
|
#1 |
|
Registered User
Join Date: Mar 2005
Location: Melissa, TX
Posts: 799
|
I need 3 drive shaft measurements, please?
All are for SWB with small block.
1) Long tail TH350 2) Short tail TH350 3) TH400 Also, what are the measurements for the actual transmissions? I know I have a TH350, however, I don't know if it is a long or short tail.
__________________
68 short bed driver (71 clip on it now, swapping to 68 when weather cooperates) 67 short step project (will get SWB from the 68) 67 Camaro, #'s matching (my wife's) 03 Dodge Ram 2500 4x4 diesel 5 speed 4.10 rear Last edited by fade94; 06-11-2006 at 10:43 PM. Reason: Added motor info. |
|
|
|
06-11-2006, 09:34 PM
|
#2 |
|
71 GMC 454/TH400
Join Date: Dec 2005
Location: Blue Mound TX
Posts: 214
|
Re: I need 3 drive shaft measurements, please?
My big block and turbo 400 drive shaft measures 68" center joint to center joint. The short shaft 350 tail shafy should be around 6" I think. I can get some exacts on that tomarrow.
__________________
"The bigger you are the harder you fall, the farther you walk the longer you crawl." |
|
|
|
|
06-11-2006, 09:54 PM
|
#3 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
|
Re: I need 3 drive shaft measurements, please?
a small block with a short shaft TH350 in a SWB truck would be 4 foot 10 inches.
|
|
|
|
|
06-12-2006, 07:17 PM
|
#4 |
|
71 GMC 454/TH400
Join Date: Dec 2005
Location: Blue Mound TX
Posts: 214
|
Re: I need 3 drive shaft measurements, please?
Here is a bad pic of a short shaft 350
__________________
"The bigger you are the harder you fall, the farther you walk the longer you crawl." Last edited by farmtruckIII; 06-12-2006 at 07:18 PM. |
|
|
|
|
06-13-2006, 04:30 PM
|
#5 |
|
Senior Member
 
Join Date: Jan 2005
Location: Claremore, OK 74017
Posts: 2,639
|
Re: I need 3 drive shaft measurements, please?
I measured my two piece on my 69 - I have a 350 eng with TH-350 tranny that has a 6 inch tail. The front shaft was 25 inches from center to center and the rear is 35 center to center.
__________________
68 Short Stepside C-10 69 SWB C-10 70 Flatbed C-20 70 LWB C-20 BB402 70 LWB C-10 CST 70 LWB C-10 CST 71 Short Stepside Cheyenne C-10 72 LWB C-10 72 Blazer 4x4 4spd 95 Jeep Cherokee 4x4 |
|
|
|
|
06-13-2006, 04:42 PM
|
#6 |
|
Junior Member
Join Date: Apr 2006
Location: Eufaula, OK
Posts: 103
|
Re: I need 3 drive shaft measurements, please?
A TH400 is around 29" long.
__________________
Clif '68 C/10 LWB, 327, TH400, 12 bolt |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
