![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Jan 2000
Location: The Netherlands
Posts: 1,063
|
Were to put an oil temp sensor?
Well the title says it all basicly.
I've tried the oil pan, but it leaked a little bit and I wanted to tighten it a bit more but it broke off, leaving me with a lot of cleaning to do on the floor in front of my house ![]() The adapter plug broke in half. The part that was still inside the oilpan I luckely got it out without any problems. So is there any other place where I can put this oil temp sensor in a Small Block? Thanks in advance for any ideas. Cya, Edmond Dutch Longhorn ![]()
__________________
1971 Chevy C/20 Longhorn, 350/TH400, Edelbrock Performer, IMPCO 425 LPG Carb 1974 Chevy Camaro Z28 (Original) ------------------------- The Netherlands |
![]() |
![]() |
![]() |
#2 | |
JamesChurch13
Join Date: May 2006
Location: Edwards AFB Sunny California
Posts: 151
|
Re: Were to put an oil temp sensor?
Quote:
![]()
__________________
HG/FTW!!! ![]() Current vehicle collection: 1968 Chevy C-10 SWB Fleet Side, 327ci, TH350 (MD) 1987 Chevy Dually Quad Cab, 427ci, TH400 2008 Buell XB12SS, 1203cc 2006 YZ450F Wheelie Machine! 1997 Suzuki Bandit 600cc And the Wife has some cars I pay insurance on and use to transport the kids!(01' Grand Cherokee and 06' Pontiac Grand Prix) |
|
![]() |
![]() |
![]() |
#3 | |
Registered User
Join Date: Jan 2000
Location: The Netherlands
Posts: 1,063
|
Re: Were to put an oil temp sensor?
Quote:
But maybe I should try the newer gaskets they sell at the dealer, the ones with the rubber insert. (GM Part # 14090908) Thanks James Cya, Edmond Dutch Longhorn ![]()
__________________
1971 Chevy C/20 Longhorn, 350/TH400, Edelbrock Performer, IMPCO 425 LPG Carb 1974 Chevy Camaro Z28 (Original) ------------------------- The Netherlands |
|
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: Jan 2001
Location: Middlesex, NC
Posts: 231
|
Re: Were to put an oil temp sensor?
Oil temp huh? OK, well, I would personally just tee the connector for the oil pressure on the back of the block (just behind the intake) and go from there.
Orlando
__________________
70 C-20 Custom Camper Build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=300251 |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Jan 2005
Location: LAX area, So Cal
Posts: 499
|
Re: Were to put an oil temp sensor?
When I was running an LT1 in my 240Z, I plumbed the oil temp sensor in the oil pan. I pulled the pan and welded a nut to to it. I was then able to really crank down on the sensor to crush the copper washer creating a good seal...never had a drop of oil from it. I used some hylemar on the threads for double protection, but it was likely unnecessary....
Tim
__________________
1972 Suburban C20 454/TH700R4, eaton-corporate 4.10 (looking for 3.7) Sold: 71 Cheyenne 20 Installed a 99 5.7L L31/4L60E from Suburban 1500 (2005) |
![]() |
![]() |
![]() |
Bookmarks |
|
|