|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
11-21-2006, 06:58 PM
|
#1 |
|
diggertodd
Join Date: May 2005
Location: Athens, Illinois
Posts: 132
|
ash tray removal problems
I am so afraid I'm going to look stupid asking this one...
Four fasteners removed from Ash tray housing 2 up under the slide opening and 2 outer fasteners on the lower side - it will not budge - are ther spot welds??? - now is your formal invitation to make me look stupid 
|
|
|
|
11-21-2006, 07:14 PM
|
#2 |
|
Senior Member
Join Date: Dec 2004
Location: Southern Pines NC
Posts: 3,853
|
Re: ash tray removal problems
Not me..................
|
|
|
|
|
11-21-2006, 07:59 PM
|
#3 |
|
The Older Generation
   
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,774
|
Re: ash tray removal problems
Talk about dumb... I just took mine out a couple of weeks ago and I'll be damned if I can remember. I thought there was just the four screws. Does the radio brace fasten to the back of it? Unless someone else answers I will check mine out in the morning....
 LockDoc I couldn't stand it, I had to go look. There are four screws, two at the top of the ashtray opening and two above the heater control behind the dash.... I don't know if you can get to the ones behind the dash without taking the heater control out or not. Nothing else that fastened to mine. LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - Last edited by LockDoc; 11-21-2006 at 08:12 PM. Reason: More info |
|
|
|
|
11-21-2006, 08:04 PM
|
#4 |
|
Registered User
Join Date: Aug 2006
Location: Georgia
Posts: 850
|
Re: ash tray removal problems
I don't think there are any spot welds because I removed mine back during the first part of the year. I can't remember how exactly I removed it but there were no spot welds. Sorry I couldn't be of more help.
|
|
|
|
|
11-21-2006, 08:21 PM
|
#5 |
|
diggertodd
Join Date: May 2005
Location: Athens, Illinois
Posts: 132
|
Re: ash tray removal problems
The answer is.... drum roll ....
I slightly separated the ash tray from the dash panel until it showed two spot welds right beside the upper screw holes - figure that one out - masking taped the dash off and hit it with a die grinder - fell out...  It was factory welds too, the original paint was up in the fitment of each.
Last edited by diggertodd; 11-21-2006 at 08:22 PM. |
|
|
|
|
11-21-2006, 08:44 PM
|
#6 |
|
The Older Generation
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,774
|
Re: ash tray removal problems
-
I've never seen one put in that way... So much to learn, so little time...  LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
|
|
|
11-21-2006, 10:02 PM
|
#7 |
|
Senior Member
Join Date: Jul 2004
Location: Estherville, Iowa
Posts: 3,371
|
Re: ash tray removal problems
What year is your truck?
__________________
1968 C10 307 3spd Long Fleet ------ http://67-72chevytrucks.com/vboard/s...d.php?t=201103 1970 C10 305 Super T10 Long Fleet --- http://67-72chevytrucks.com/vboard/s...d.php?t=202285 1971 C20 383 TH350 Dana Posi ----- http://67-72chevytrucks.com/vboard/s...d.php?t=206894 2001 GMC Sierra 1500 C3 6.0 |
|
|
|
|
11-22-2006, 07:10 AM
|
#8 |
|
Registered User
Join Date: Apr 2006
Location: oklahoma
Posts: 10,669
|
Re: ash tray removal problems
Ah yes I have seen a few spot welded. I found them on a janesville truck. pita to remove. I think I also had to do it on a couple of st louis trucks to. Is yours an a/c truck? All that I have found spot welded were a/c trucks. Hope this helps.
|
|
|
|
|
11-22-2006, 10:24 AM
|
#9 |
|
diggertodd
Join Date: May 2005
Location: Athens, Illinois
Posts: 132
|
Re: ash tray removal problems
yep, 1970 A/C truck - now with cracks in the dash paint from me trying to animal-out a frakin ash tray...
|
|
|
|
|
11-22-2006, 01:01 PM
|
#10 |
|
Registered User
Join Date: Sep 2006
Location: Lancaster, PA
Posts: 270
|
Re: ash tray removal problems
I had a 70 non-ac with the spot welds. Maybe it's a 1970 thing?!?!
|
|
|
|
|
11-22-2006, 05:00 PM
|
#11 |
|
Wrenchin & Sandin!!!
Join Date: Aug 2006
Location: Joliet, IL.
Posts: 523
|
Re: ash tray removal problems
FYI....My 71 non-ac cab did not have any welds. Just the 4 screws
__________________
Randy  Shorewood, IL. My Favorite eBay Searches My Driver Restore Thread 1971 C10 Longbed 2005 Silverado Shortbed 2005 FXDWG Last edited by Draggn66; 11-22-2006 at 10:08 PM. |
|
|
|
|
11-22-2006, 10:06 PM
|
#12 |
|
Senior Member
Join Date: Mar 2001
Location: Cedar Park, TX
Posts: 686
|
Re: ash tray removal problems
...My 71 non-ac cab has the ash tray bracket spot welded in...
__________________
71 Chevy C-10 SWB Fleetside RamJet-350/4L60e & Compushift/3.73Posi See it at www.prismnet.com/~grzanich |
|
|
|
|
11-22-2006, 10:13 PM
|
#13 |
|
4 eyed fever
Join Date: Jul 2005
Location: Eureka, Nevada
Posts: 500
|
Re: ash tray removal problems
My 71 non/ac is spot welded, but i had a 71 non a/c that wasn't, a 70 with a/c that was not, and a 72 non a/c that wasn't. Maybe the assembly plant made the call?
__________________
1971 GMC 2500 4x4 1972 GMC Sierra Grande 1/2 t 4x4-#1 son's truck. Recently completed resto. 4 YO daughter," Daddy, I like your truck better than Mom's." (2000 F350-ranch truck) Smart kid!! |
|
|
|
|
11-23-2006, 08:57 AM
|
#14 |
|
Senior Member
Join Date: Jul 2002
Location: northern IL.
Posts: 263
|
Re: ash tray removal problems
71 air cab spot welded
|
|
|
|
|
11-23-2006, 11:08 AM
|
#15 |
|
Registered User
Join Date: Apr 2006
Location: oklahoma
Posts: 10,669
|
Re: ash tray removal problems
Ok so how about you list what plants the ones that came spot welded.
72 stlouis a/c- welded 71 janesville a/c- welded 72 flint non a/c- screwed Lets here yours. Last edited by Aarons72s; 11-23-2006 at 11:25 AM. |
|
|
|
|
11-23-2006, 11:22 AM
|
#16 |
|
Wrenchin & Sandin!!!
Join Date: Aug 2006
Location: Joliet, IL.
Posts: 523
|
Re: ash tray removal problems
Ok my non-air 71 was made in Oshawa.
__________________
Randy Shorewood, IL. My Favorite eBay Searches My Driver Restore Thread 1971 C10 Longbed 2005 Silverado Shortbed 2005 FXDWG |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
