The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-08-2007, 12:51 PM   #1
Ole Blue 68
Registered User
 
Ole Blue 68's Avatar
 
Join Date: Aug 2005
Location: Philly
Posts: 1,140
Inline Fuel Filter

Alright, I've sprung a leak on my second inline fuel filter in less than 6 months so I gotta be doing something wrong. The first was a glass one and I figured it was just the filter but this second one was an all metal one from Edelbrock that seemed pretty solid.

My fuel line is steel till about the manifold and then it's rubber up to the carb so I cut the rubber line about halfway up and put the filter in there. I saw somewhere that said you shouldn't put the filter higher than your manifold (of course, after I had already put it on).

Anybody got any info on this?
Ole Blue 68 is offline   Reply With Quote
Old 01-08-2007, 01:01 PM   #2
WorkinLonghorn
Senior Member
 
WorkinLonghorn's Avatar
 
Join Date: Dec 2006
Location: Studio City, Calif.
Posts: 2,883
Re: Inline Fuel Filter

I don't understand,the filter is leaking,or the fuel line? Did I read this right? ( I'm pre-coffee here). I've got an in-line filter same place as you and have never had a problem except maybe a loose clamp. If the LINE is leaking (you are using approved fuel line I'm sure) replace it. If the filter is leaking get a better filter.
Because my side tanks are kinda crusty inside,I use a large filter about the size of a lawn mower muffler and occasionally have to blow it out or replace it.
I don't think it should matter about the location.-cougar
__________________
'69 GMC C2500 Custom Camper, 8 1/2' bed, New GM 350, NP 435 Close Ratio 4spd. Trans., 3.73 Dana-60 open.Camper and Trailer wiring, PS, PB, AC, tach , three gas tanks, stereo speakers, 2nd owner, Work-Truck supreme.
WorkinLonghorn is offline   Reply With Quote
Old 01-08-2007, 01:08 PM   #3
Ole Blue 68
Registered User
 
Ole Blue 68's Avatar
 
Join Date: Aug 2005
Location: Philly
Posts: 1,140
Re: Inline Fuel Filter

The filter's leaking not the line. I figured it was quality of the filter the first time around but the second one's an Edelbrock and it's pretty hefty.
Ole Blue 68 is offline   Reply With Quote
Old 01-08-2007, 01:36 PM   #4
WorkinLonghorn
Senior Member
 
WorkinLonghorn's Avatar
 
Join Date: Dec 2006
Location: Studio City, Calif.
Posts: 2,883
Re: Inline Fuel Filter

That's pretty weird. I got mine at the local cheapo parts place and got the biggest one they had,due to the unique problem I had. You sure the clamp wasn't a bit loose and gas got sprayed onto the filter?
__________________
'69 GMC C2500 Custom Camper, 8 1/2' bed, New GM 350, NP 435 Close Ratio 4spd. Trans., 3.73 Dana-60 open.Camper and Trailer wiring, PS, PB, AC, tach , three gas tanks, stereo speakers, 2nd owner, Work-Truck supreme.
WorkinLonghorn is offline   Reply With Quote
Old 01-08-2007, 01:39 PM   #5
Ole Blue 68
Registered User
 
Ole Blue 68's Avatar
 
Join Date: Aug 2005
Location: Philly
Posts: 1,140
Re: Inline Fuel Filter

At first, I thought it might be the clamps but couldn't tighten 'em anymore and then when I looked closer I could still see gas dripping off the the filter.

Quote:
Originally Posted by cougar View Post
That's pretty weird. I got mine at the local cheapo parts place and got the biggest one they had,due to the unique problem I had. You sure the clamp wasn't a bit loose and gas got sprayed onto the filter?
Ole Blue 68 is offline   Reply With Quote
Old 01-08-2007, 02:38 PM   #6
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,776
Re: Inline Fuel Filter

-
Without looking at it it's hard to say but I would bet it's leaking somewhere else and running down onto the filter. First thing I would do would be to replace the rubber fuel hose. Make sure you get fuel line and not vacuum hose.....

LockDoc
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-
LockDoc is offline   Reply With Quote
Old 01-08-2007, 03:21 PM   #7
Longhorn Man
its all about the +6 inches
 
Longhorn Man's Avatar
 
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
Re: Inline Fuel Filter

your location is fine... it's under the truck you don't want to put the filter.
Longhorn Man is offline   Reply With Quote
Old 01-08-2007, 05:41 PM   #8
Ole Blue 68
Registered User
 
Ole Blue 68's Avatar
 
Join Date: Aug 2005
Location: Philly
Posts: 1,140
Re: Inline Fuel Filter

I'll double check after work today but I'm pretty sure it was coming from the filter. Unless I got a pinhole leak somewhere on the back of the hose....

Quote:
Originally Posted by LockDoc View Post
-
Without looking at it it's hard to say but I would bet it's leaking somewhere else and running down onto the filter. First thing I would do would be to replace the rubber fuel hose. Make sure you get fuel line and not vacuum hose.....

LockDoc
Ole Blue 68 is offline   Reply With Quote
Old 01-08-2007, 07:05 PM   #9
Fred T
Cantankerous Geezer
 
Fred T's Avatar
 
Join Date: Aug 2002
Location: Bel Aire, KS
Posts: 6,264
Re: Inline Fuel Filter

I've had problems with fuel line leaks and filters. I think everyone has. Usually they're so small you don't notice them. One problem is the screw style clamps, they don't seal evenly. The old spring clamps work best. Also, a sealant can be used. Permatex Hylomar is a non-hardening sealant developed by Rolls-Royce for gasoline contact. Only one that I know of, buy it at the auto parts store. Smear a hylomar on the nipples before assembly.

The problem with putting the filter below the manifold is due to leakage. My 52 has the filter between the tank and pump, it used to slowly drain the fuel out of the line, meaning it took a while cranking to start if it sat for more than a day. The hylomar took care of that very small leak, nd the problem stopped.
__________________
Fred

There is no such thing as too much cam...just not enough engine.
Fred T is offline   Reply With Quote
Old 01-08-2007, 07:46 PM   #10
Longhorn Man
its all about the +6 inches
 
Longhorn Man's Avatar
 
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
Re: Inline Fuel Filter

havin the filter between the tank and pump can also cause or worsen vapor lock conditions.
Longhorn Man is offline   Reply With Quote
Old 01-08-2007, 08:44 PM   #11
MisterMan
Account Suspended
 
MisterMan's Avatar
 
Join Date: Jan 2006
Location: Visalia, California
Posts: 286
Re: Inline Fuel Filter

some of thoes cheap filters will leak if vibrating too much.
MisterMan is offline   Reply With Quote
Old 01-08-2007, 10:59 PM   #12
gyjackson
Registered User
 
Join Date: Jan 2007
Location: arkansas
Posts: 29
Re: Inline Fuel Filter

It would be a good idea to replace the rubber lines and clamps.....cheap anyway....besides you have probably leaked more than enuff gas to pay for a whole new line from the pump up. Fuel pressure should only be 5-10psi max. Even a beer can will handle twice that pressure. I bet your filter is fine. A quick test, take it out of the line, let it dry put a finger over one end, a piece of hose on the inlet (with clamp), stick it under water and blow in the hose. (bubbles tell no lies).....Good luck!!
gyjackson is offline   Reply With Quote
Old 01-09-2007, 10:13 AM   #13
Ole Blue 68
Registered User
 
Ole Blue 68's Avatar
 
Join Date: Aug 2005
Location: Philly
Posts: 1,140
Re: Inline Fuel Filter

Well I looked it over yesterday after work and it was the filter after all. Even though it's all an metal unit and pretty hefty, the housing must have vibrated loose. I tightened it and re-installed. Hopefully that will be the end of it. If it happens again, I'll try some sealant. And if that don't work, I'm yanking it out.
Ole Blue 68 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:03 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com