Can't Change Air From Vents To Heater - The 1947 - Present Chevrolet & GMC Truck Message Board Network

DANL · 11-23-2002, 11:36 PM

Anyone have advice for problem with the HVAC system on my 72 K5. I can not divert the air from the vents to heater or defroster. When I move the control lever, the cable moves arm on box. I can also hear the flap moving inside the box. But the air continues to come out of vents. Any recommendations or advise would be appreciated.
Thanks in advance.

...Dan

Ackattack · 11-24-2002, 12:39 AM

I've had the same problem. The diverter flap was broken along the bar where it rotates. I ended up super gluing it back together and it works. You could also by a new diverter box or a salvage yard piece, but I'm cheap.

DANL · 11-24-2002, 02:37 PM

Thanks Ack.

...Dan

Hooter · 11-24-2002, 08:11 PM

Isnt there a rubber gasket around the door? If there is it might be all cracked
I had a similar problem on my 77 silverado, turns out the heater box was full of pencils, pens, nails and a screwdriver. Don't store crap on the top of the dash

DANL · 11-24-2002, 11:41 PM

Thanks Hooter!
I plan to get into this weekend.

...Dan

mtdave2 · 11-25-2002, 01:25 AM

ya im sure its that door. it breaks right near the pivot pin. im even cheaper than you guys, i got 2 large washers and some really good epoxy. glued 1/2 the washer on the door and the other 1/2 on the part still connected to the pin.. works well. almost 2 years no trouble

DANL · 11-25-2002, 09:48 AM

Thanks MT.
Looking forward to it not costing much.

...Dan

johnnyp · 11-25-2002, 10:22 AM

Want a really cheap fix? Here's how the PO solved the problem. Works ok but it can be a little tricky to close or open while you're driving. I decided to go with a new box.

chevy2racr · 11-25-2002, 04:18 PM

I was thinkin about doin somethign lke the last pic, but I'm not sure what you guys are sayin is broken. mine I took apart to replace the heatr core last winter and it didn't work whn I got it togeter, took it apart and pushed the flap up so it was in the heater vent direction. summer, I slide the lever and it goes back, took itapart this fall to flip it again, and just recently the defrost to heater changer stopped workin. I can move the slide but it stays at little on defrost, rest of heater(floor)
any ideas?

chevy2racr · 11-25-2002, 11:49 PM

ttt

DANL · 11-26-2002, 01:31 AM

That is deffinitely cheap Johnnyp.
Chevy2racr I think my problem is with the first diverter controlled by the ac.

...Dan

chevy2racr · 11-29-2002, 04:09 PM

any ideas for me to look for?

DANL · 11-29-2002, 07:35 PM

I am not an expert, and not sure I understand your problem, but it could be cable related. Is your cable moving diverter arm required distance?

...Dan

11-23-2002, 11:36 PM	#1
DANL Senior Member Join Date: Mar 2002 Location: Bartlett, TN Posts: 348	Can't Change Air From Vents To Heater Anyone have advice for problem with the HVAC system on my 72 K5. I can not divert the air from the vents to heater or defroster. When I move the control lever, the cable moves arm on box. I can also hear the flap moving inside the box. But the air continues to come out of vents. Any recommendations or advise would be appreciated. Thanks in advance. ...Dan

11-24-2002, 12:39 AM	#2
Ackattack Senior Member Join Date: Aug 2002 Location: Valley Center KS Posts: 3,524	I've had the same problem. The diverter flap was broken along the bar where it rotates. I ended up super gluing it back together and it works. You could also by a new diverter box or a salvage yard piece, but I'm cheap. __________________ Project Bruiser: 68 Pro-Touring C-10 5.3L / 4L60E Project Ironhide: 97 GMC Crew Cab 4x4 Cummins SOLD: '69 GMC 1/2T SWB TBI'd: Project No Buck Assembly Manual Index Sign up Thread!!! Factory Service Manual Index

11-24-2002, 08:11 PM	#4
Hooter My other Love Join Date: Aug 2001 Location: Castlegar B.C. Canada Posts: 4,085	Isnt there a rubber gasket around the door? If there is it might be all cracked I had a similar problem on my 77 silverado, turns out the heater box was full of pencils, pens, nails and a screwdriver. Don't store crap on the top of the dash __________________ Castlegar B.C.The great white North (Canada Eh!) Hooter_5@hotmail.com First generation Monte Carlo club pictures of my life

11-25-2002, 01:25 AM	#6
mtdave2 newly minted old timer Join Date: Dec 1999 Location: Hudson WI Posts: 3,521	ya im sure its that door. it breaks right near the pivot pin. im even cheaper than you guys, i got 2 large washers and some really good epoxy. glued 1/2 the washer on the door and the other 1/2 on the part still connected to the pin.. works well. almost 2 years no trouble __________________ ____________________________________________ 72 c20 longhorn 65k org miles and counting! 69 k10 Suburban

11-25-2002, 10:22 AM	#8
johnnyp Keepin' It Stock Join Date: Aug 2001 Location: Grand Island, Nebraska, USA Posts: 554	Want a really cheap fix? Here's how the PO solved the problem. Works ok but it can be a little tricky to close or open while you're driving. I decided to go with a new box. Attached Images __________________ 72 Sierra Grande - Maych Forget about "do it right the first time". Do it wrong the first time to learn how, then do it right the second time.

11-24-2002, 02:37 PM	#3
DANL Senior Member Join Date: Mar 2002 Location: Bartlett, TN Posts: 348	Thanks Ack. ...Dan

11-24-2002, 11:41 PM	#5
DANL Senior Member Join Date: Mar 2002 Location: Bartlett, TN Posts: 348	Thanks Hooter! I plan to get into this weekend. ...Dan

11-25-2002, 09:48 AM	#7
DANL Senior Member Join Date: Mar 2002 Location: Bartlett, TN Posts: 348	Thanks MT. Looking forward to it not costing much. ...Dan

11-25-2002, 04:18 PM	#9
chevy2racr So Many Ideas, So Little Money Join Date: Sep 2001 Location: Marshalltown, IA Posts: 1,610	I was thinkin about doin somethign lke the last pic, but I'm not sure what you guys are sayin is broken. mine I took apart to replace the heatr core last winter and it didn't work whn I got it togeter, took it apart and pushed the flap up so it was in the heater vent direction. summer, I slide the lever and it goes back, took itapart this fall to flip it again, and just recently the defrost to heater changer stopped workin. I can move the slide but it stays at little on defrost, rest of heater(floor) any ideas? __________________ 72 Blazer 3/4 ton running gear 4.10s NP205/TH350 350 4in lift half doors 71 C10 with 454 99 S-10 5.1L SBC 700R4 09 Malibu Marshalltown, Iowa

11-25-2002, 11:49 PM	#10
chevy2racr So Many Ideas, So Little Money Join Date: Sep 2001 Location: Marshalltown, IA Posts: 1,610	ttt __________________ 72 Blazer 3/4 ton running gear 4.10s NP205/TH350 350 4in lift half doors 71 C10 with 454 99 S-10 5.1L SBC 700R4 09 Malibu Marshalltown, Iowa

11-26-2002, 01:31 AM	#11
DANL Senior Member Join Date: Mar 2002 Location: Bartlett, TN Posts: 348	That is deffinitely cheap Johnnyp. Chevy2racr I think my problem is with the first diverter controlled by the ac. ...Dan

11-29-2002, 04:09 PM	#12
chevy2racr So Many Ideas, So Little Money Join Date: Sep 2001 Location: Marshalltown, IA Posts: 1,610	any ideas for me to look for? __________________ 72 Blazer 3/4 ton running gear 4.10s NP205/TH350 350 4in lift half doors 71 C10 with 454 99 S-10 5.1L SBC 700R4 09 Malibu Marshalltown, Iowa

11-29-2002, 07:35 PM	#13
DANL Senior Member Join Date: Mar 2002 Location: Bartlett, TN Posts: 348	I am not an expert, and not sure I understand your problem, but it could be cable related. Is your cable moving diverter arm required distance? ...Dan



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.