race harness with factory buckets - The 1947 - Present Chevrolet & GMC Truck Message Board Network

avysittinon22s · 08-06-2007, 08:11 PM

Is it possible for me to install a 4-point race harness and use seats from a 90-94 full size Chevy truck? I already have the seats and dont wanta have to get race seats.

**Palf70Step** · 08-06-2007, 08:29 PM

Best bet is to check your local laws. Many areas do not permit 4 point harnesses for use in street machines.

Yes the late model seats will work. You will need some floor bracing to make it safe though.

avysittinon22s · 08-06-2007, 08:49 PM

How could I get the the two shoulders straps to to hold in place without slipping off the top of the seat?

Longhorn Man · 08-06-2007, 09:27 PM

actually, that would fall under ederal law, but many cops have no idea how that works.
To install a 4 point haness properly in a truck like this, you'll have to start with a roll bar.

*Shane* · 08-06-2007, 09:45 PM

... or go THRU the seats and anchor the two shoulder belts to the floor BEHIND and UNDER the seats

Longhorn Man · 08-06-2007, 09:57 PM

that would compress your spine in an accident, and this is exactly why these type of seat belts are not DOT aproved, too many ppl would cause more harm then good if everyone was installing them.
If they are to be anchored directly behinde the seat, they have to be at mid sho8ulder level IIRC. If you could anchor them a couple feet back, they cvan go to the floor without hurting you.
An NHRA track tech inspector could tell you exactly how to do it, and I assume the NHRA rule book would have it too.
Or maybe Simpson's web site.

71Dragtruck · 08-07-2007, 12:04 AM

http://www.nhra.com/contacts/tech_faq.html

It's hard to see in the pic, but the belts need to be fastened behind you level with the top of your shoulders, or if fastened to the floor wrap around the back cross bar that is level with the top of your shoulders. As stated before, if the belts are just fastened to the floor, they will pull down on your shoulders compressing your spine and crushing it.

I know that you are using factory seats, but still applies if you don't install them right you'll do yourself more harm then good. So that said, if they are attached behind you to the cross bar, that will hold them up for you, then just bring them around the sides of the seat.

GREASEMONKEY72 · 08-07-2007, 12:19 AM

just make a plate and weld it to the ledge of the cab just under the window and make sure the belts are at or above your shoulder height and the lap blets you can also make a couple plates off the floor to bolt them to

71Dragtruck - very nice set-up

08-06-2007, 08:11 PM	#1
avysittinon22s Registered User Join Date: Jun 2006 Location: Paris, TN Posts: 376	race harness with factory buckets Is it possible for me to install a 4-point race harness and use seats from a 90-94 full size Chevy truck? I already have the seats and dont wanta have to get race seats.

08-06-2007, 08:29 PM	#2
Palf70Step State of Confusion! Join Date: Jul 2002 Location: Gulfport, MS USA Posts: 47,216	Re: race harness with factory buckets Best bet is to check your local laws. Many areas do not permit 4 point harnesses for use in street machines. Yes the late model seats will work. You will need some floor bracing to make it safe though. __________________ Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God!

08-06-2007, 08:49 PM	#3
avysittinon22s Registered User Join Date: Jun 2006 Location: Paris, TN Posts: 376	Re: race harness with factory buckets How could I get the the two shoulders straps to to hold in place without slipping off the top of the seat?

08-06-2007, 09:27 PM	#4
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Re: race harness with factory buckets actually, that would fall under ederal law, but many cops have no idea how that works. To install a 4 point haness properly in a truck like this, you'll have to start with a roll bar.

08-06-2007, 09:45 PM	#5
Shane Account Suspended Join Date: Jun 2000 Location: over yonder Posts: 14,270	Re: race harness with factory buckets ... or go THRU the seats and anchor the two shoulder belts to the floor BEHIND and UNDER the seats

08-06-2007, 09:57 PM	#6
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Re: race harness with factory buckets that would compress your spine in an accident, and this is exactly why these type of seat belts are not DOT aproved, too many ppl would cause more harm then good if everyone was installing them. If they are to be anchored directly behinde the seat, they have to be at mid sho8ulder level IIRC. If you could anchor them a couple feet back, they cvan go to the floor without hurting you. An NHRA track tech inspector could tell you exactly how to do it, and I assume the NHRA rule book would have it too. Or maybe Simpson's web site.

08-07-2007, 12:04 AM	#7
71Dragtruck Registered User Join Date: Jun 2004 Location: Saskatchewan, Canada Posts: 1,368	Re: race harness with factory buckets http://www.nhra.com/contacts/tech_faq.html It's hard to see in the pic, but the belts need to be fastened behind you level with the top of your shoulders, or if fastened to the floor wrap around the back cross bar that is level with the top of your shoulders. As stated before, if the belts are just fastened to the floor, they will pull down on your shoulders compressing your spine and crushing it. I know that you are using factory seats, but still applies if you don't install them right you'll do yourself more harm then good. So that said, if they are attached behind you to the cross bar, that will hold them up for you, then just bring them around the sides of the seat. Attached Images __________________ Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs Last edited by 71Dragtruck; 08-07-2007 at 12:21 AM.

08-07-2007, 12:19 AM	#8
GREASEMONKEY72 Registered User Join Date: Aug 2006 Location: Bakersfield,CA Posts: 7,893	Re: race harness with factory buckets just make a plate and weld it to the ledge of the cab just under the window and make sure the belts are at or above your shoulder height and the lap blets you can also make a couple plates off the floor to bolt them to 71Dragtruck - very nice set-up __________________ -steven Alte Seele S.S. "Allison" '72 C/10 LWB 350SB/TH350 - DD PITBULL IS NOT A CRIME Last edited by GREASEMONKEY72; 08-07-2007 at 12:20 AM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.