Rust pics, YAY!

[lyrikz]

Here are some pics of my rust, and a pic of what parts i would need to order.
Here is the diagram.


Here is a pic of the rocker rust. Those two circled spots are all the way through. The other two pictures are what it looks like from the bottom. What numbers on that diagram do i have to order for those parts??? Those wholes are DIRECTLY below the circled pictures.

[killthewabbit]

Don't be ashamed of your rust. It's a badge of honor.

[CUSTOM/10]

Here's what I would use, this and an outer rocker. You wouldn't have to use the whole thing if you don't need to.
Gary

http://www.tri-proautomotive.com/ser...IES-ONE/Detail

[lyrikz]

Originally Posted by CUSTOM/10

Here's what I would use, this and an outer rocker. You wouldn't have to use the whole thing if you don't need to.
Gary

http://www.tri-proautomotive.com/ser...IES-ONE/Detail

Will that one piece cover the whole area i need? or do i need the rocker with that, or use the one i have???

[CUSTOM/10]

Looks like that will take care of the areas of the floor and inner rocker that need to be replaced, but you'll also need to get an outer rocker. How are the cab supports ??? ( #'s 12,13,14 & 15 )

[lyrikz]

Originally Posted by CUSTOM/10

Looks like that will take care of the areas of the floor and inner rocker that need to be replaced, but you'll also need to get an outer rocker. How are the cab supports ???

Cab supports and everything else is A+ under there. Needs to be cleaned and por15 and undercoated but thats it....

So i need the inner floor and the outer rocker?? So in that top diagram, would i need #4,11,8 and 9???

[raggedjim]

You don't need 8 or 11. you need 4 lh & rh and 9 lh & rh. Item 4 will include 8 & 11 stamped in.

Or you can skip item 4 and use items 2 & 3 both lh & rh. This is what we used to do before item 4 was available (you'll do a little more cutting and welding, but you will spend about $100.00 less) This is the way I have always done it. Wait a minute! I just checked the link custom/10 posted. THAT'S what I would get, same part as LMC at a much better price.
Good luck, Rg

[lyrikz]

Originally Posted by raggedjim

You don't need 8 or 11. you need 4 lh & rh and 9 lh & rh. Item 4 will include 8 & 11 stamped in.

Or you can skip item 4 and use items 2 & 3 both lh & rh. This is what we used to do before item 4 was available (you'll do a little more cutting and welding, but you will spend about $100.00 less) This is the way I have always done it.

Good luck, Rg

Left hand and right hand?? Only the drivers side has any issues. So i need 4 and 9... Thanks for the help.

[raggedjim]

Sorry, I thought you had problems on both sides. Looks like you have an easy fix.

I think I might consider buying the outer rocker only and cutting out the bad sections of the inner. You could take the cut out section to a sheet metal shop (hvac guys usually can do it too) and have them bend up some pieces to weld in. Might save some $

Good luck, Rg

[lyrikz]

Originally Posted by raggedjim

Sorry, I thought you had problems on both sides. Looks like you have an easy fix.

I think I might consider buying the outer rocker only and cutting out the bad sections of the inner. You could take the cut out section to a sheet metal shop (hvac guys usually can do it too) and have them bend up some pieces to weld in. Might save some $

Good luck, Rg

So 4, and 9.... Alrighty... Thanks again for the help....

[CUSTOM/10]

I didn't even notice part #4 in the LMC picture, that's the same as the piece in the link that I sent. But the one from Tri-Pro is $40 less !!!

Gary

[lyrikz]

Originally Posted by CUSTOM/10

I didn't even notice part #4 in the LMC picture, that's the same as the piece in the link that I sent. But the one from Tri-Pro is $40 less !!!

Gary

custom. If i ordered that link you posted, then just got an outer rocker i should be golden right???

[lyrikz]

Originally Posted by lyrikz

custom. If i ordered that link you posted, then just got an outer rocker i should be golden right???

WOW, i like that site, they have everything there... Pretty inexpensive also.. I got what you mentioned plus an outter rocker. see how that goes...

I need to call up GMC paul and place the big order.

[mfarmer]

Call up GMC Pauls and get them there. They will get you the correct items and they will talk to you and make sure you get the correct pieces. Plus they will be cheaper.

[CUSTOM/10]

You should be golden, you can use the whole thing or just cut out the bad area and trim the new piece to fit. You'll know better how much of the piece you'll need once you get the outer rocker off. Get yourself a spotweld drill that will make removing the outer rocker easier.

Gary

[jb4short]

Originally Posted by mfarmer

Call up GMC Pauls and get them there. They will get you the correct items and they will talk to you and make sure you get the correct pieces. Plus they will be cheaper.

LOL...we talk to people....they just need to call; but a lot of people prefer to just order online

[lyrikz]

Originally Posted by Tri-ProAutomotive

LOL...we talk to people....they just need to call; but a lot of people prefer to just order online

Tri.
I did place an order from you guys on tuesday 9/25 and received an email confirmation, but no email that my stuff has shipped.

Any ideas??
Del Emerson
runnin46@hotmail.com

[lyrikz]

Originally Posted by lyrikz

Tri.
I did place an order from you guys on tuesday 9/25 and received an email confirmation, but no email that my stuff has shipped.

Any ideas??
Del Emerson
runnin46@hotmail.com

Oh, also. I liked your ordering process and parts pictures alot better then GMCPauls, and they were less money...

I still am getting the bed kit through paul. ahaha And a few other things...

[jb4short]

Originally Posted by lyrikz

Tri.
I did place an order from you guys on tuesday 9/25 and received an email confirmation, but no email that my stuff has shipped.

Any ideas??
Del Emerson
runnin46@hotmail.com

It's a glitch we're trying to work out with the host of our storefront...I'll go get your tracking number. It shipped out immediately; and we appreciate the business

[jb4short]

Originally Posted by lyrikz

Oh, also. I liked your ordering process and parts pictures alot better then GMCPauls, and they were less money...

I still am getting the bed kit through paul. ahaha And a few other things...

I need a bed kit also

[Longhorn Man]

I'm not trying to cut anyone out of any buinesess here... but you have a vendor just a few miles from you in Olimpia... Wes at Classic heart beat. He is a board supporter, and has a very good rep.
Two of the other vendors mentioned here are also outstanding vendors, also supporters of the site... but LMC totally sucks, I wouldn't spend a dime there unless they were the ONLY way to get rolling.

[lyrikz]

Originally Posted by Longhorn Man

I'm not trying to cut anyone out of any buinesess here... but you have a vendor just a few miles from you in Olimpia... Wes at Classic heart beat. He is a board supporter, and has a very good rep.
Two of the other vendors mentioned here are also outstanding vendors, also supporters of the site... but LMC totally sucks, I wouldn't spend a dime there unless they were the ONLY way to get rolling.

I use LMC for their catalog.. I havent and wouldnt ever order from them... There are things im getting from paul. And i will be meeting Wes this saturday to pick up my steel cowl hood for my truck.. Does he do any discounting for us members?? And i already ordered parts from Tri, and will be ordering more parts very soon...