|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
11-25-2007, 09:36 AM
|
#1 |
|
Registered User
Join Date: Jan 2005
Location: Australia
Posts: 215
|
Neat comp cam selection program
I found this nice program from competition cams for selecting a cam , gives estimated horsepower and torque, a bit like desktop dyno.
Dunno how accurate it is maybe someone can compare it with desktop and let us know, here's the link www.competitioncams.com |
|
|
|
11-25-2007, 10:09 AM
|
#2 |
|
Senior Member
Join Date: Aug 2005
Location: tulsa OK
Posts: 3,070
|
Re: Neat comp cam selection program
got a more specific link???
|
|
|
|
|
11-25-2007, 10:50 AM
|
#3 |
|
Registered User
 
Join Date: Nov 2007
Location: Grande Prairie, Alberta
Posts: 30
|
Re: Neat comp cam selection program
I checked it out, you need to download the program (comp cams software) 20MB, after you install it you need to enter all your engine specs( heads, flow, valves, basic cam selection, intake & flow) pretty neat if you have that information.
|
|
|
|
|
11-25-2007, 12:18 PM
|
#4 |
|
Registered User
Join Date: May 2005
Location: PA
Posts: 2,696
|
Re: Neat comp cam selection program
I built mine up, and the curves/numbers it produced looked almost exact to what Desktop Dyno did over on Billa's thread in the engine section.
|
|
|
|
|
11-25-2007, 05:46 PM
|
#5 |
|
Need a bigger hammer..
Join Date: Feb 2007
Location: Escondido,CA.
Posts: 280
|
Re: Neat comp cam selection program
Cool, saving that one for my 454 build.
__________________
1968 GMC 3/4 LWB fleetside Custom Camper 2018 Silverado High Country 2500HD Duramax 4X4 |
|
|
|
|
11-25-2007, 07:43 PM
|
#6 |
|
67-72 Addict!
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,857
|
Re: Neat comp cam selection program
Cool, I downloaded and played with it a bit. I'm assuming it's roughly 20% or so above real life numbers. It's amazing what a good set of heads and a little bump in c/r will do for a motor!. I need heads,lol.
__________________
Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads |
|
|
|
|
11-26-2007, 12:56 AM
|
#7 | |
|
Registered User
Join Date: May 2005
Location: PA
Posts: 2,696
|
Re: Neat comp cam selection program
Quote:
|
|
|
|
|
|
11-26-2007, 12:46 PM
|
#8 |
|
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Neat comp cam selection program
That's a cool little app, thanks for the link...
__________________
Beat it to fit, Paint it to match... 
|
|
|
|
|
11-26-2007, 02:12 PM
|
#9 |
|
Registered User
Join Date: Feb 2007
Location: Star Valley, WY
Posts: 2,038
|
Re: Neat comp cam selection program
i monkeyed with it last night. for some reason it will not let me tailor the bore and stroke from stock. anyone else have this issue?
__________________
Steve 1971 GMC Longbox. Full Roller Stroker 489 w/ FiTech EFI, Chris Straub Cam/NV4500/205/D60/14B w. Grizzly Locker and 4.11's. 2" Lift on 33's |
|
|
|
|
11-26-2007, 02:20 PM
|
#10 | |
|
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Neat comp cam selection program
Quote:
__________________
Beat it to fit, Paint it to match...
|
|
|
|
|
|
11-26-2007, 02:35 PM
|
#11 |
|
Registered User
Join Date: Feb 2007
Location: Star Valley, WY
Posts: 2,038
|
Re: Neat comp cam selection program
i have a stoked mkIV block though. i select 454 and it wont allow me to change the bore and stroke. am i missing something somewhere??
__________________
Steve 1971 GMC Longbox. Full Roller Stroker 489 w/ FiTech EFI, Chris Straub Cam/NV4500/205/D60/14B w. Grizzly Locker and 4.11's. 2" Lift on 33's |
|
|
|
|
11-26-2007, 02:41 PM
|
#12 |
|
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Neat comp cam selection program
I just stroked a 454 to 571. Click to the right of the bore or stroke and type in your numbers and hit return...
__________________
Beat it to fit, Paint it to match...
|
|
|
|
|
11-26-2007, 03:46 PM
|
#13 |
|
Registered User
Join Date: Feb 2007
Location: Star Valley, WY
Posts: 2,038
|
Re: Neat comp cam selection program
ok...got it!
__________________
Steve 1971 GMC Longbox. Full Roller Stroker 489 w/ FiTech EFI, Chris Straub Cam/NV4500/205/D60/14B w. Grizzly Locker and 4.11's. 2" Lift on 33's |
|
|
|
|
11-27-2007, 12:21 PM
|
#14 |
|
Registered User
Join Date: Feb 2007
Location: Star Valley, WY
Posts: 2,038
|
Re: Neat comp cam selection program
has anybody figured out the head selection on this program? i'm unsure what my Eddy 454-O semi-open chambers would be considered on the drop down menu.
__________________
Steve 1971 GMC Longbox. Full Roller Stroker 489 w/ FiTech EFI, Chris Straub Cam/NV4500/205/D60/14B w. Grizzly Locker and 4.11's. 2" Lift on 33's |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
