Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
03-15-2008, 09:20 AM | #1 |
Registered User
Join Date: Feb 2007
Location: Cali Central Coast
Posts: 5,191
|
gas tank grommet question...
Can you replace the grommet without pulling the tank out? Stupid question, maybe, but I've never done it before and don't want to cut the old one out before I realize what's involved.
__________________
'67 SWB Fleetside ZZ4/350/Tremec 5-speed/4link/Scott's IFS - and fun as heck! SOLD Click here to support the board Philippians 4: 6-7 |
03-15-2008, 09:53 AM | #2 |
Self-proclaimed LED man
Join Date: Nov 2003
Location: Harrisburg, Missouri
Posts: 1,021
|
Re: gas tank grommet question...
Yes, but you have to be very careful. Cut it out from the backside with a razor knife. Try warming the new gromet up under a spotlight or something to make it softer. I've replaced them without removing them, so i know it's possible
Justin
__________________
My LED Website My Photobucket Album of LED's Ask me about hand-made custom L.E.D brake and reverse lights. <- LINK I also do LED: -Third Brake/Cargo -Brake (truck and burb) -Reverse (truck and burb) -67-68 Front Turn Signals -69-70 Front Turn Signals -71-72 Front Turn Signals -GMC Front Turn Signals I can also do custom lights for other vehicles....i did a set for a AMC Gremlin once Norwood Survivor Last edited by 724x4a/cchevy; 03-15-2008 at 09:53 AM. |
03-15-2008, 01:55 PM | #3 |
Registered User
Join Date: Jan 2002
Location: Elizabethtown, KY, USA
Posts: 136
|
Re: gas tank grommet question...
Interesting...That happens to be about exactly where I am at..even looks like your truck was the same yellow as mine. Let me know how it works for you, but since I have the seat out, I will probably pull the tank anyhow.
__________________
My Truck: 1968 C-20 Custom Camper |
03-15-2008, 05:22 PM | #4 |
Registered User
Join Date: May 2005
Location: PA
Posts: 2,696
|
Re: gas tank grommet question...
Is this straightforward when the tank is out? Or is there a trick to doing it then too?
Getting ready to upgrade fuel system, and might as well do a new gromet while swapping tanks. |
03-15-2008, 06:43 PM | #5 |
Like a Rock!
Join Date: May 2002
Location: USA
Posts: 1,092
|
Re: gas tank grommet question...
Cut it out and smear dish liquid to the new one and slide it on. Easy! No need to pull the tank for a 2 minute job.
__________________
69 LWB Runs great - work in progress Mess with me and you mess with the whole trailer park! |
03-15-2008, 06:45 PM | #6 |
Registered User
Join Date: Feb 2007
Location: Cali Central Coast
Posts: 5,191
|
Re: gas tank grommet question...
I'll let you know how it turns out - I'm gonna do it this weekend.
__________________
'67 SWB Fleetside ZZ4/350/Tremec 5-speed/4link/Scott's IFS - and fun as heck! SOLD Click here to support the board Philippians 4: 6-7 |
03-15-2008, 07:05 PM | #7 |
Registered User
Join Date: Mar 2004
Location: CA
Posts: 2,057
|
Re: gas tank grommet question...
|
03-15-2008, 07:56 PM | #8 |
Registered User
Join Date: May 2005
Location: PA
Posts: 2,696
|
Re: gas tank grommet question...
Thanks
|
03-17-2008, 06:48 AM | #9 |
Registered User
Join Date: Feb 2007
Location: Cali Central Coast
Posts: 5,191
|
Re: gas tank grommet question...
I looked at it and I chickened out - The grommet is rock hard and hard to get to, and I have to take my seat out again anyways, so I'll wait.
__________________
'67 SWB Fleetside ZZ4/350/Tremec 5-speed/4link/Scott's IFS - and fun as heck! SOLD Click here to support the board Philippians 4: 6-7 |
03-17-2008, 08:32 AM | #10 | |
Registered User
Join Date: Jun 2007
Location: oregon
Posts: 1,069
|
Re: gas tank grommet question...
Quote:
Been there done that!!!!!
__________________
69 K-20 cloned to a 67 with front clip and some other stuff. 383 .040 over Crane roller cam lifters and rockers ,1.6 intake ratio, Open chamber heads, 9.5-1 compression ratio, 2.02 intake valves , Edelbrock performer Air Gap manifold Carter AFB performer 750cfm, MSD ignition, SM465 NP205 4.10 gears: |
|
03-17-2008, 08:36 AM | #11 |
Active Member
Join Date: May 2007
Location: SO CAL
Posts: 226
|
Re: gas tank grommet question...
its a easy install just replaced mine a few months back
|
03-17-2008, 09:03 AM | #12 |
Registered User
Join Date: Feb 2007
Location: Cali Central Coast
Posts: 5,191
|
Re: gas tank grommet question...
Well, now you got me thinking - maybe I'l try tomorrow. If I can't get it I can always pull the tank, I have to pull the seat anyways. I'll let you know how it turns out.
__________________
'67 SWB Fleetside ZZ4/350/Tremec 5-speed/4link/Scott's IFS - and fun as heck! SOLD Click here to support the board Philippians 4: 6-7 |
03-17-2008, 10:51 AM | #13 | |
Registered User
Join Date: Jun 2007
Location: oregon
Posts: 1,069
|
Re: gas tank grommet question...
Quote:
Aerostotle be my name!!!!
__________________
69 K-20 cloned to a 67 with front clip and some other stuff. 383 .040 over Crane roller cam lifters and rockers ,1.6 intake ratio, Open chamber heads, 9.5-1 compression ratio, 2.02 intake valves , Edelbrock performer Air Gap manifold Carter AFB performer 750cfm, MSD ignition, SM465 NP205 4.10 gears: |
|
Bookmarks |
|
|