Hood repair sheet metal - The 1947 - Present Chevrolet & GMC Truck Message Board Network

sprbxr · 08-10-2008, 10:03 PM

Does anyone make a repair section for the lower front section of the hood on a 66 C10? I can't seem to find another hood that isn't rotted out in the same place. The lower section on the front of the hood and the corners are pretty rotted too.

Thanks
Justin
66 SWB Fleetside

jonzcustomshop · 08-10-2008, 10:06 PM

There is a guy that sells this piece on ebay every now and then, I think he had one listed this week.
I do think that cars inc, or dynacorn makes a patch panel for the piece as well.

ClassicAutoResto · 08-10-2008, 10:27 PM

Time to get out the tin snips and hammer!

sprbxr · 08-10-2008, 10:37 PM

Quote:

Originally Posted by ClassicAutoResto

Time to get out the tin snips and hammer!

I have considered do it that way but if I can find a decent repro I will buy to to save myself some time.
Justin

sprbxr · 08-10-2008, 11:02 PM

I checked the Cars, Inc and Dynacorn site but neither show that section. In fact, the Cars, Inc site skips 60-66 trucks altogether.
Justin

Hillbilly Deluxe 65 · 08-11-2008, 12:45 AM

i talked to a guy at the super chevy show in richmond, va that worked for i lost his card but the name was like classic somethin i tryed lookin on google for it but he said they would be selling them by september

jonzcustomshop · 08-11-2008, 07:34 AM

classic industries?
I saw a fullk page ad showing the front section , and I think a full repro hood as well, I remember thinking why spend all that time and labor on a patch, when you could just buy a whole hood...

mbgmike · 08-11-2008, 05:55 PM

The upper entire front is now being produced but not the lower that I am aware of. We sell the upper from TriPlus for $175.00. Kind of expensive. The hoods are hard to find in good shape but if you just need the lower section its not as hard. We find plenty of banged up ones where the bottom is ok

Hillbilly Deluxe 65 · 08-12-2008, 01:53 PM

well wheres the best place to buy a new hood repro or fiberglass

mbgmike · 08-12-2008, 06:07 PM

I don't know of anyone reproducing a complete steel hood right now. You would have to go F/G. Some of the others may know a good source. We do not sell any f/g parts

Hillbilly Deluxe 65 · 08-12-2008, 10:57 PM

thanks for the input any takers??

**Captainfab** · 08-13-2008, 10:49 PM

Quote:

Originally Posted by Hillbilly Deluxe 65

well wheres the best place to buy a new hood repro or fiberglass

Well you have basically 3 choices:

http://www.usbody.com

http://www.up22.com

http://www.showcars-bodyparts.com

I haven't bought from any of these yet, but I've heard some negative feedback on US Body's parts.

Hillbilly Deluxe 65 · 08-14-2008, 12:57 AM

Quote:

Originally Posted by Captainfab

Well you have basically 3 choices:

http://www.usbody.com

http://www.up22.com

http://www.showcars-bodyparts.com

I haven't bought from any of these yet, but I've heard some negative feedback on US Body's parts.

thanks alot man i think im gonna go with the 2in cowl from show cars

08-10-2008, 10:03 PM	#1
sprbxr Registered User Join Date: Aug 2008 Location: peaks. va Posts: 3	Hood repair sheet metal Does anyone make a repair section for the lower front section of the hood on a 66 C10? I can't seem to find another hood that isn't rotted out in the same place. The lower section on the front of the hood and the corners are pretty rotted too. Thanks Justin 66 SWB Fleetside

08-10-2008, 10:06 PM	#2
jonzcustomshop 1961 crewcab Join Date: Dec 2007 Location: missoula, mt Posts: 6,164	Re: Hood repair sheet metal There is a guy that sells this piece on ebay every now and then, I think he had one listed this week. I do think that cars inc, or dynacorn makes a patch panel for the piece as well.

08-10-2008, 10:27 PM	#3
ClassicAutoResto Rust Buster Join Date: Apr 2007 Location: Lebanon, Ky Posts: 558	Re: Hood repair sheet metal Time to get out the tin snips and hammer!

08-10-2008, 11:02 PM	#5
sprbxr Registered User Join Date: Aug 2008 Location: peaks. va Posts: 3	Re: Hood repair sheet metal I checked the Cars, Inc and Dynacorn site but neither show that section. In fact, the Cars, Inc site skips 60-66 trucks altogether. Justin

08-11-2008, 12:45 AM	#6
Hillbilly Deluxe 65 Wheelin' and Dealin' Join Date: Nov 2007 Location: poquoson va Posts: 320	Re: Hood repair sheet metal i talked to a guy at the super chevy show in richmond, va that worked for i lost his card but the name was like classic somethin i tryed lookin on google for it but he said they would be selling them by september __________________ 1965 Chevy c-10 fleetside long bed with 06 gto LS2/T56 inside Porterbuilt Extreme front and rear 12bolt w/ eaton tru-trac 4:11 gears 1BADD65 my build thread: http://67-72chevytrucks.com/vboard/s...=1#post2601700

08-11-2008, 07:34 AM	#7
jonzcustomshop 1961 crewcab Join Date: Dec 2007 Location: missoula, mt Posts: 6,164	Re: Hood repair sheet metal classic industries? I saw a fullk page ad showing the front section , and I think a full repro hood as well, I remember thinking why spend all that time and labor on a patch, when you could just buy a whole hood...

08-11-2008, 05:55 PM	#8
mbgmike Registered User Join Date: Aug 2005 Location: Pasadena,Tx /Pto Pta DR Posts: 5,415	Re: Hood repair sheet metal The upper entire front is now being produced but not the lower that I am aware of. We sell the upper from TriPlus for $175.00. Kind of expensive. The hoods are hard to find in good shape but if you just need the lower section its not as hard. We find plenty of banged up ones where the bottom is ok Last edited by mbgmike; 08-11-2008 at 06:00 PM.

08-12-2008, 01:53 PM	#9
Hillbilly Deluxe 65 Wheelin' and Dealin' Join Date: Nov 2007 Location: poquoson va Posts: 320	Re: Hood repair sheet metal well wheres the best place to buy a new hood repro or fiberglass __________________ 1965 Chevy c-10 fleetside long bed with 06 gto LS2/T56 inside Porterbuilt Extreme front and rear 12bolt w/ eaton tru-trac 4:11 gears 1BADD65 my build thread: http://67-72chevytrucks.com/vboard/s...=1#post2601700

08-12-2008, 06:07 PM	#10
mbgmike Registered User Join Date: Aug 2005 Location: Pasadena,Tx /Pto Pta DR Posts: 5,415	Re: Hood repair sheet metal I don't know of anyone reproducing a complete steel hood right now. You would have to go F/G. Some of the others may know a good source. We do not sell any f/g parts

08-12-2008, 10:57 PM	#11
Hillbilly Deluxe 65 Wheelin' and Dealin' Join Date: Nov 2007 Location: poquoson va Posts: 320	Re: Hood repair sheet metal thanks for the input any takers?? __________________ 1965 Chevy c-10 fleetside long bed with 06 gto LS2/T56 inside Porterbuilt Extreme front and rear 12bolt w/ eaton tru-trac 4:11 gears 1BADD65 my build thread: http://67-72chevytrucks.com/vboard/s...=1#post2601700



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.