![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
![]()
O.K. so many of you know I drive a yellow '47 International every day to work and various shoots, however, it is time to beef up the old 310-incher with some hot new parts, mainly because I am in a HP race at work, (number envy, its a long story.)
So editor Tommy Lee is packing a '64 Corvette with a Dart headed 350, it makes about 287 horsepower at the rear wheels (dynoed) The yellow IH is packing a 305ho that is punched out to 310 cubic inches (0.030 overbore, Comp 440 lift cam, 10.5 to 1 flat tops and iron 58cc heads. Edelbrock intake and a 500cfm carb. I am taking it down the street today to get a baseline number. I am going to install a set of High Velocity Heads, sbc aluminum heads, 175cc intake runners, 2.02/1.60 valves and beehive springs along with a new vortec style manifold and a Holley 650cfm carb. Hopeing to at least get 200 the first go around, but we will have to wait and see. I'll be sure to post the results in the morning.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride Last edited by jkaylor68gmc; 09-04-2008 at 02:13 PM. |
![]() |
![]() |
![]() |
#2 |
Old Skool Club
![]() Join Date: Jun 2001
Location: Benton, AR "The Heart of Arkansas"
Posts: 10,880
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
I'm really partial to old Cornbinders....
Yeah, we're gonna be watching to see how this turns out. Good luck. Hope you don't "blow" it...
__________________
Member Nr. 2770 '96 GMC Sportside; 4.3/SLT - Daily driven....constantly needs washed. '69 C-10 SWB; 350/TH400 - in limbo The older I get, the better I was. Last edited by ChevLoRay; 09-02-2008 at 01:15 PM. |
![]() |
![]() |
![]() |
#3 |
Registered User
![]() Join Date: Jan 2008
Location: Chesapeake Beach, MD
Posts: 812
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
Good luck!
![]() ![]()
__________________
71 cheyenne lwb 300rwhp best 1/4 time so far 12.8 @103 ![]() http://i195.photobucket.com/albums/z...en58/001-2.jpg |
![]() |
![]() |
![]() |
#4 |
I'M TRUCK CRAZY!
Join Date: Oct 2006
Location: Sachse, TEXAS
Posts: 1,737
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
(sure I'll be dissapointed)
That's funny |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
well, I saw how Tommy's Corvette did, made me sad. Rumor is these heads will make the truck hit 300 at the rear wheel or so I am told.
probably the combination of the new heads, bigger carb, better intake, aluminum roller rockers, Weiand aluminum water pump and carb spacer.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#6 |
I'M TRUCK CRAZY!
Join Date: Oct 2006
Location: Sachse, TEXAS
Posts: 1,737
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
Well, GOOD LUCK to you.
Let us know what it did. |
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
I will
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Dec 2004
Location: Northern AZ
Posts: 7,271
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
I took a summer class at UTI a few years back and the last day or two they let us play around, well I put my 94 9C1 Caprice on the rollers, 265 with a K&N FIPK kit and and flowmasters added intot he factory duals. I was shocked a bit, then realized what the flywheel numbers should be and what that motor would do in a car that was a thousand pounds lighter (4500 lbs or so in the caprice), then I wasn't so upset! Dyno's don't lie isn't 100% true, so do not get too down on yourself since there are a lot of variables on a chasis dyno.
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Oct 2005
Location: Northern Arkansas
Posts: 1,136
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
I'd like to see the 305 put up some big numbers. I've got one in my S10 Blazer with ported, and port matched H.O.heads, 9.5:1 Speed Pro pistons, Crane cam, roller tipped rockers, Action plus intake, Mallory distributor, Street Avenger 570 carb, Hedman shorty headers, and true duals that puts about 250 to the wheels. Propels my 3800# suv to a 2 sec 60ft and a 14.90 1/4 mile at 94 mph! Not too shabby for a mildly built 305. The only reason I didn't go more radical was because it's my everyday driver. And it gets 16mpg in town. I'd guess 300hp from a 305 would be pretty easy to accomplish, and 400+ from a 305 stroker.
|
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
thats good to know, I am going to a DynoJet which is suppose to be 20 percent higher than a Mustang. Not real sure though.
my truck weighs 2685 with 3/4 of a tank of fuel.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#11 |
Like a Rock!
Join Date: May 2002
Location: USA
Posts: 1,092
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
I predict you will make close to your buddy's 350
![]()
__________________
69 LWB Runs great - work in progress Mess with me and you mess with the whole trailer park! ![]() |
![]() |
![]() |
![]() |
#12 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
O.K. so I went to the Dyno and I am sad, i feel that I have been touched wrongly.
The best run up to 4 was the red line 145 horsepower, OUCH! We found that the throttle pedal was not pulling the carb to wide open throttle. AFter making the adjustments we hit 175 horsepower and 242 on torque. I was sad but with the new top end and maybe a FI kit later I should be able to hit 300. We'll have to see, I am about to begin the teardown.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#13 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
Here is the dyno sheet, you can see the difference between 3/4 throttle and full throttle.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#14 |
Registered User
Join Date: Mar 2005
Location: 10-Uh-See
Posts: 5,609
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
I suggest keeping the 500 cfm carb. The 650 will bog it down at lower rpms. It might make more peak HP, but throttle response and driveability will be better with the 500.
With all things considered, 175 at the rear wheels with a 305 is pretty darn good. That means your touching the 250-275 hp mark at the flywheel with accessories. If the engine were on a dyno with no accessories, it would probably be in the 300-315 range. I doubt my mild cammed 350 would do that well. Also, if you don't mind me asking, where did you have the dyno done and about how much does it cost? I'm interested in having my truck dynoed just for the fun of it.
__________________
Last edited by 68Stepbed; 09-03-2008 at 08:56 AM. |
![]() |
![]() |
![]() |
#15 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
He told me I would be making a ton more at the crank but I have the three biggest power killers
700R4 12 Bolt truck rear Massive 20-inch rollers with big tires.... oooppppss
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#16 |
Registered User
Join Date: Aug 2008
Location: Lantana, TX
Posts: 419
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
He's right, the 12 bolt doesn't hurt you too much. What kinda stall are you running, they will eat up the power on a dyno.
|
![]() |
![]() |
![]() |
#17 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
I am not quite for sure, I will have to try and find the dyno report for my trans, it is a TCI deal.
He said the 12 bolt WAS hurting me.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride Last edited by jkaylor68gmc; 09-03-2008 at 09:23 AM. |
![]() |
![]() |
![]() |
#18 |
Registered User
Join Date: Aug 2008
Location: Lantana, TX
Posts: 419
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
It does hurt you compared to a 10 bolt sure, but it's not going to suck up 20+ rwhp. On 4th gen Camaro's 12 bolts only take maybe 10-15 rwhp to spin up. The wheels take up a lot of power, I lost about 10 just switching from factory 16's to chrome 18's, so I bet 20's are even worse. The biggest culprit is your auto and whatever stall you are running.
|
![]() |
![]() |
![]() |
#19 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
yeah, I know, just means I will have to make more power at the crank. The dyno guy told me I might be losing as much as 30 percent. Thats O.k I look good doing it.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#20 | |
Hittin E-Z Street on Mud Tires
![]() Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
Quote:
What's important is do you enjoy driving the truck? ![]() But seriously, that's some nice power for a 2,700lb truck! 2.2L S-10's only make about 88-90 hp at the rear wheels (no I'm not joking ![]() My 67 weights about 3,700lbs and I'd be lucky if my late 70's 350 makes 200 hp at the flywheel ![]()
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride ![]() American Born, Country by the Grace of God ![]() 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! |
|
![]() |
![]() |
![]() |
#21 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
yeah, I just want some more power and the dang office race isn't helping anything either.
WIll/ Super Rod Cadillac CTS-V 365 horsepower at the wheels Tommy/ Chevy RUmble '64 Corvett 286 horsepower at the wheels ME / Truck Builder '47 IH 175 horsepower at the wheels.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#22 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
I have alot of catching up to do.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#23 |
Hittin E-Z Street on Mud Tires
![]() Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
Just drop one of these in instead. You may need to beef up the 700R4 for it though...
http://www.edelbrock.com/media/news/.../081407-9.html ![]() *It's a little bit on the expensive side ![]()
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride ![]() American Born, Country by the Grace of God ![]() 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! |
![]() |
![]() |
![]() |
#24 |
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
Ya think? I would rather keep my short block, it new, clean, runs great, just a few bolt-ons is all.
aluminum heads, new intake, bigger carb, roller rockers, new pushrods and an aluminum water pump should do the trick.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
![]() |
![]() |
![]() |
#25 |
Hittin E-Z Street on Mud Tires
![]() Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Going to the Dyno at 6:00 (sure I'll be dissapointed)
Yeah, just givin' you an "ass kickin'" option
![]() Do you have a clutch fan or electric fans? That's good for a couple/few hp as well.
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride ![]() American Born, Country by the Grace of God ![]() 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! Last edited by 67ChevyRedneck; 09-03-2008 at 11:40 AM. |
![]() |
![]() |
![]() |
Bookmarks |
|
|