Cleaning out the shed, misc stuff, and parting the last truck out. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

masterbeavis · 11-02-2008, 01:38 PM

All parts are located in Placerville CA, unless otherwise noted. I will get pics up asap. I have moved again for the fourth time this year, this stuff is begining to become a burden to move around. I have more crap to list once I get unburied.

I have two pairs of HD 44 hubs. Three of them have the blue dial, one has the yellow. They all appear to be in mechanically excellent shape, however two of the blue dials have broken out on the inside, I have not gotten around to repairing them. The chrome is typical of 30+ years. Its there, not flaking off, but dinged. Spicer script is missing on most of them.

These are pics of the ones with the damaged dials.

68-72 Blazer seat frames. Seats are shot, has the correct brackets. I would rather sell the complete pair of seats, rather than part with the seat brackets. $50 for the whole shooting match, $75 for the brackets alone.

GMC center console. Cracked and modified in the usual ways, for the most part, in pretty lousy condition. Grey in color. $20

Two glovebox doors. $10 each

Factory AM radio, condition unknown. The chrome is in so so condition, I have no knobs for it. $10

69 327 block. Has the casting number correct for a Camaro, but the suffix for a fullsize car. Block is fully seasoned(aka rusty), and ready for a complete rebuild. 2 bolt main. $50

Eaton HO72 rear ends. One is from a 72 with the large studs, the other is older. Both have the large brakes, open carriers, and 4.10 gears. The newer one has has the brake linings stick to the drums, but it will break free once it is installed onto a vehicle. $150 each, located in Fiddletown CA.

H052/072 5.14 third member, open. Located in fiddletown CA. $250

1 pair of 327 camel hump heads, 3782461, pre 68 castings. They look extremely clean, possibly rebuilt They do not have accessory bosses, or water temp bungs. They are clean of carbon and junk buildup, but would need to be ran thru the steam cleaner or something to get lint, dirt, etc off before you run them. $200

Factory steel upper radiator hoses. I have to verify I still have those, will post a price once they appear.

Chevy 350, GM crate motor, used, unknown mileage, ran great when pulled, installed a HIPO motor. No accessories, longblock only. $100

GM 5.7l Diesel motor. Complete minus alternator. Located in shingle springs CA $75

Misc junk is also available from a 69 half ton LWB truck. Body is pretty much toast, has an I6 without power steering.

**BIGJAKE97** · 11-02-2008, 02:27 PM

i'll take the seats. pm being sent -jake

**6t727t2** · 11-02-2008, 02:30 PM

Price on the hubs? Thanks

va_tlc · 11-02-2008, 05:48 PM

price on blue 3/4 hubs and are thhe ones these the ones that are broken? thanks 24477

**BIGJAKE97** · 11-04-2008, 11:43 PM

picked up seats, and a couple of other things! thanks again. nice doing bussiness with you. you were real easy to deal with and would buy from again. it's allways nice meeting board members and checking out their trucks and parts! -jake

masterbeavis · 11-05-2008, 01:49 AM

Jake, thanks for the kind words.

I will get pics up of the other hubs tommorow hopefully, and confirm I still have the plastic pieces for the ones that are pictured.

**special-K** · 11-05-2008, 06:41 AM

We need a price for those hubs.

masterbeavis · 11-05-2008, 12:25 PM

Quote:

Originally Posted by special-K

We need a price for those hubs.

Well, seeing how you are going to make me shoot from the hip, I will say $150 a pair for the damaged ones, $200 for the blue/yellow dial ones. When I dig them out of the shed, I will price them accordingly.

oski6754 · 01-14-2010, 08:54 PM

Do you happen to have a GMC tailgate in decent condition?

usmcchevy · 01-14-2010, 09:27 PM

Um, I don't think you're going to get a reply. This post is from Nov 2008 and the member hasn't been on here since July.

**special-K** · 01-15-2010, 09:01 AM

...and,as title/description reads,these are the last of the parts he has...had.

masterbeavis · 08-04-2010, 09:40 PM

Quote:

Originally Posted by oski6754

Do you happen to have a GMC tailgate in decent condition?

I do have a decent GMC tailgate, however its attached to a 71 Jimmy I am now trying to get rid of.

oski6754 · 08-04-2010, 09:46 PM

No worries. Found one locally. Thanks!

11-02-2008, 01:38 PM	#1
masterbeavis Having issues Join Date: Jul 2005 Location: Eldorado Ca, an hour east of sacramento Posts: 696	Cleaning out the shed, misc stuff, and parting the last truck out. All parts are located in Placerville CA, unless otherwise noted. I will get pics up asap. I have moved again for the fourth time this year, this stuff is begining to become a burden to move around. I have more crap to list once I get unburied. I have two pairs of HD 44 hubs. Three of them have the blue dial, one has the yellow. They all appear to be in mechanically excellent shape, however two of the blue dials have broken out on the inside, I have not gotten around to repairing them. The chrome is typical of 30+ years. Its there, not flaking off, but dinged. Spicer script is missing on most of them. These are pics of the ones with the damaged dials. 68-72 Blazer seat frames. Seats are shot, has the correct brackets. I would rather sell the complete pair of seats, rather than part with the seat brackets. $50 for the whole shooting match, $75 for the brackets alone. GMC center console. Cracked and modified in the usual ways, for the most part, in pretty lousy condition. Grey in color. $20 Two glovebox doors. $10 each Factory AM radio, condition unknown. The chrome is in so so condition, I have no knobs for it. $10 69 327 block. Has the casting number correct for a Camaro, but the suffix for a fullsize car. Block is fully seasoned(aka rusty), and ready for a complete rebuild. 2 bolt main. $50 Eaton HO72 rear ends. One is from a 72 with the large studs, the other is older. Both have the large brakes, open carriers, and 4.10 gears. The newer one has has the brake linings stick to the drums, but it will break free once it is installed onto a vehicle. $150 each, located in Fiddletown CA. H052/072 5.14 third member, open. Located in fiddletown CA. $250 1 pair of 327 camel hump heads, 3782461, pre 68 castings. They look extremely clean, possibly rebuilt They do not have accessory bosses, or water temp bungs. They are clean of carbon and junk buildup, but would need to be ran thru the steam cleaner or something to get lint, dirt, etc off before you run them. $200 Factory steel upper radiator hoses. I have to verify I still have those, will post a price once they appear. Chevy 350, GM crate motor, used, unknown mileage, ran great when pulled, installed a HIPO motor. No accessories, longblock only. $100 GM 5.7l Diesel motor. Complete minus alternator. Located in shingle springs CA $75 Misc junk is also available from a 69 half ton LWB truck. Body is pretty much toast, has an I6 without power steering. __________________ Quando Omni Flunkus Moritati. The Man's Prayer: "I'm a man, but I can change, if I have to, I guess."

11-02-2008, 02:27 PM	#2
BIGJAKE97 Senior Member Join Date: May 2005 Location: hayward, ca Posts: 268	Re: Cleaning out the shed, misc stuff, and parting the last truck out. i'll take the seats. pm being sent -jake __________________ 67 short fleet 71 blazer 4x4 72 blazer 2wd 76 gmc sierra 3/4t 4x4 62 bel air 01 blazer extreme member 11,943!

11-02-2008, 02:30 PM	#3
6t727t2 Active Member Join Date: Dec 2004 Location: NJ Posts: 6,456	Re: Cleaning out the shed, misc stuff, and parting the last truck out. Price on the hubs? Thanks

11-02-2008, 05:48 PM	#4
va_tlc Registered User Join Date: Nov 2005 Location: VIRGINIA Posts: 905	Re: Cleaning out the shed, misc stuff, and parting the last truck out. price on blue 3/4 hubs and are thhe ones these the ones that are broken? thanks 24477 __________________ 1969 rs 1966fastback 1969swbc/10 2006gt 1972swb4x4

11-04-2008, 11:43 PM	#5
BIGJAKE97 Senior Member Join Date: May 2005 Location: hayward, ca Posts: 268	Re: Cleaning out the shed, misc stuff, and parting the last truck out. picked up seats, and a couple of other things! thanks again. nice doing bussiness with you. you were real easy to deal with and would buy from again. it's allways nice meeting board members and checking out their trucks and parts! -jake __________________ 67 short fleet 71 blazer 4x4 72 blazer 2wd 76 gmc sierra 3/4t 4x4 62 bel air 01 blazer extreme member 11,943!

11-05-2008, 01:49 AM	#6
masterbeavis Having issues Join Date: Jul 2005 Location: Eldorado Ca, an hour east of sacramento Posts: 696	Re: Cleaning out the shed, misc stuff, and parting the last truck out. Jake, thanks for the kind words. I will get pics up of the other hubs tommorow hopefully, and confirm I still have the plastic pieces for the ones that are pictured. __________________ Quando Omni Flunkus Moritati. The Man's Prayer: "I'm a man, but I can change, if I have to, I guess."

11-05-2008, 06:41 AM	#7
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Cleaning out the shed, misc stuff, and parting the last truck out. We need a price for those hubs. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ Last edited by special-K; 11-05-2008 at 06:41 AM.

01-14-2010, 08:54 PM	#9
oski6754 Registered User Join Date: May 2009 Location: Los Angeles, CA Posts: 178	Re: Cleaning out the shed, misc stuff, and parting the last truck out. Do you happen to have a GMC tailgate in decent condition?

01-14-2010, 09:27 PM	#10
usmcchevy Has more rust than truck... Join Date: Apr 2005 Location: Ivanhoe, MN Posts: 2,421	Re: Cleaning out the shed, misc stuff, and parting the last truck out. Um, I don't think you're going to get a reply. This post is from Nov 2008 and the member hasn't been on here since July. __________________ 1972 Custom/10 SWB, 4.8/4l80e Build thread LSx Swap FAQ index

01-15-2010, 09:01 AM	#11
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Cleaning out the shed, misc stuff, and parting the last truck out. ...and,as title/description reads,these are the last of the parts he has...had. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

08-04-2010, 09:46 PM	#13
oski6754 Registered User Join Date: May 2009 Location: Los Angeles, CA Posts: 178	Re: Cleaning out the shed, misc stuff, and parting the last truck out. No worries. Found one locally. Thanks!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.