The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-07-2008, 04:53 PM   #1
Tx Firefighter
Watch out for your cornhole !
 
Tx Firefighter's Avatar
 
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
All right cab light guys, I need guidance here

I'm about to put a set of cab lights on my 3/4 ton which didn't have them factory.



How did you run the wiring ?

I'm thinking I might be able to pull the driver side sun visor out and fish the wires through the hole, but how did you run them down the pillar to the dash ? Front or rear pillar ?

I have a factory headliner in my truck and it's nice, so I really don't want to disturb it to drill holes behind it.
__________________
I'm on the Instagram- @Gearhead_Kevin
Tx Firefighter is offline   Reply With Quote
Old 12-07-2008, 05:17 PM   #2
72armyswbtruck
Registered User
 
72armyswbtruck's Avatar
 
Join Date: Feb 2004
Location: Idaho
Posts: 4,033
Re: All right cab light guys, I need guidance here

From the ligths that I have removed, the wiring harness ran down the driver side front windshield pillar, there is a hollow access point that allows the wire to go all the way down and drop out by the e-brake, and the ground wire screws onto the cab body under the steering column.
__________________
"Remember, They can Kill You, but they can't eat You, That's against the law!!!!!!!!!"
72armyswbtruck is offline   Reply With Quote
Old 12-07-2008, 06:10 PM   #3
CG
BlahBlahBlah
 
Join Date: Feb 2002
Location: Wa.
Posts: 20,021
Re: All right cab light guys, I need guidance here

I have an NOS set of lights and harness. It looks like its installed pretty much the way 72army says...On the pieces that goes down the drivers side pillar the two wire harness has a protective cord type coating and ends in two spade connectors that must plug into the light switch somewhere.
CG is offline   Reply With Quote
Old 12-07-2008, 06:29 PM   #4
Tx Firefighter
Watch out for your cornhole !
 
Tx Firefighter's Avatar
 
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
Re: All right cab light guys, I need guidance here

I've been looking all day and darned if I can figure out what little nook they ran them through. It must have been done while spot welding the cab together originally or something.
__________________
I'm on the Instagram- @Gearhead_Kevin
Tx Firefighter is offline   Reply With Quote
Old 12-07-2008, 07:24 PM   #5
special-K
Special Order

 
special-K's Avatar
 
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
Re: All right cab light guys, I need guidance here

I put them on a truck that didn`t come with them.It`s been so long,but I`m pretty sure I ran the wire up the windshield post.I remember removing the visor and pulling through the whole,then pulling whole to whole.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed"

GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project)
GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling)
Tim

"Don't call me a redneck. I'm a rough cut country gentleman"

R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~
special-K is offline   Reply With Quote
Old 12-07-2008, 08:33 PM   #6
72armyswbtruck
Registered User
 
72armyswbtruck's Avatar
 
Join Date: Feb 2004
Location: Idaho
Posts: 4,033
Re: All right cab light guys, I need guidance here

I will try and get some pics. It is much easier once you hae the holes on the roof cut. I might even have some pics on the home computer.
__________________
"Remember, They can Kill You, but they can't eat You, That's against the law!!!!!!!!!"
72armyswbtruck is offline   Reply With Quote
Old 12-07-2008, 09:00 PM   #7
Longhorn Man
its all about the +6 inches
 
Longhorn Man's Avatar
 
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
Re: All right cab light guys, I need guidance here

like I was tellin you in PM... I spent many hrs on mine and said screw it as far as running the wires right.
Hope you have better luck.
Longhorn Man is offline   Reply With Quote
Old 12-07-2008, 10:44 PM   #8
Tx Firefighter
Watch out for your cornhole !
 
Tx Firefighter's Avatar
 
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
Re: All right cab light guys, I need guidance here

Andy, I finally got fed up with it and ran the wire inside the door seal from the dash to the top. Then I drilled a tiny hole and ran the wire into the cavity on top of the cab and through to the sunvisor hole.

Tomorrow, I start fishing the individual cab light wires to the sunvisor hole and connect them all to the power wire.
__________________
I'm on the Instagram- @Gearhead_Kevin
Tx Firefighter is offline   Reply With Quote
Old 12-07-2008, 11:17 PM   #9
Longhorn Man
its all about the +6 inches
 
Longhorn Man's Avatar
 
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
Re: All right cab light guys, I need guidance here

Sounds kinda familiar! I'll have to see if I can get a photo of how I ran mine.
Longhorn Man is offline   Reply With Quote
Old 12-08-2008, 12:33 AM   #10
chevy29267truck
Account Suspended
 
Join Date: Sep 2008
Location: Alva Florida
Posts: 668
Re: All right cab light guys, I need guidance here

ok for the lights on the roof of the truck cabs from the right too the left 3 1/8 in the front 25 in the mindly 2 all too the left 3 1/8
chevy29267truck is offline   Reply With Quote
Old 12-08-2008, 01:25 AM   #11
bucket
Registered User
 
bucket's Avatar
 
Join Date: Aug 2001
Location: Shawnee, KS
Posts: 923
Re: All right cab light guys, I need guidance here

i'm getting ready to do this too. i don't think you can go up the rear pillar. there is a pinch weld along the roof back there. i was going to try a fish tape inside the driver pillar.

the mice have to get up there somehow....
__________________
79 K10
77 MGB
79 Kawasaki KZ1000
bucket is offline   Reply With Quote
Old 12-08-2008, 06:35 AM   #12
special-K
Special Order

 
special-K's Avatar
 
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
Re: All right cab light guys, I need guidance here

Quote:
Originally Posted by Tx Firefighter View Post
Andy, I finally got fed up with it and ran the wire inside the door seal from the dash to the top. Then I drilled a tiny hole and ran the wire into the cavity on top of the cab and through to the sunvisor hole.

Tomorrow, I start fishing the individual cab light wires to the sunvisor hole and connect them all to the power wire.
The show judges frown upon such things.You`ll never get a best of show like that.Would prolly knock 10 grand off at Barrett-Jackson,too.But,it`s your truck...lol
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed"

GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project)
GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling)
Tim

"Don't call me a redneck. I'm a rough cut country gentleman"

R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~
special-K is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:50 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com