Wiper removal not going well - The 1947 - Present Chevrolet & GMC Truck Message Board Network

6600DURAMAX · 02-17-2009, 06:03 PM

AAAGGHHHGGAAAHHHH WIPERS will not come off – Had to remove the front clip with the cowl in place!! I know the little clip gets pushed up then the wiper should slide off but it is not working!!! I need them off without doing any more damage to the front clip or cowl.

Any tips – I might just have to take a sawzall to the top of them and buy new ones????

thanks guys

Andy4639 · 02-17-2009, 06:16 PM

Go to napa and buy this handy dandy tool and it will come right off.

*67/72junkie* · 02-17-2009, 06:17 PM

You need a couple of pieces of scrape leather or old shoe to pad the cowl and protect from damage.2 large ,about 1/2 to 5/8 wide flat screw drivers.1 on each side twisted up with eqaul pressure usually pops them right off.

Botietruck · 02-17-2009, 06:23 PM

I took a bondo spreader and cut a semi-circle out of the thin tapered edge. It slips right around the shaft and protects the paint.

jsbgump · 02-17-2009, 06:28 PM

I guess i need to find the nearest napa to me. I can't find the tool on there website

thirdstreettito · 02-17-2009, 06:37 PM

I undid the clip, then grabbed with pliers and pulled VERY hard.

ChevLoRay · 02-17-2009, 08:34 PM

NAPA also has a tool that is plier-like in that you squeeze the handles and lift the wiper off of the splined shaft. The tool has plasticized parts that protect both wiper and paint. As far as the one above is concerned, I've never seen one like that.....not saying it doesn't work, I just haven't seen one.

The tool, at NAPA, that I'm talking about is somewhere around $10, if my memory doesn't leave me stupid.

chevy_mike · 02-17-2009, 09:52 PM

On my last '68, I had to cut one of them off. Even with the clip removed, it would not budge. Cut off wheel and it was done.

I was replacing the arms anyways so I had nothing to loose and did not want to screw up the splined part.

Good luck!

6600DURAMAX · 02-17-2009, 11:29 PM

Thanks guys, I will go and get a tool and try it if not I will use a cutoff wheel (better that my idea of a sawzall)

thanks guys - once again this site is Great

cdowns · 02-17-2009, 11:40 PM

some times things slide better when lubricated

Andy4639 · 02-17-2009, 11:40 PM

Sorry guy's I said Napa in the first post should of said Snap on. Sorry!

Yellow67C10 · 02-18-2009, 12:35 AM

Perfect timing on this thread. I am trying toremove the wiper arms on our 1957 Belair and found the same problem..........Now thanks to everyone her I've found the answer to how do this. Thanks everyone.

mrein3 · 02-18-2009, 02:27 PM

I love the "internets" (as our former President once said).

I have always had a hard time removing wiper arms. I've always got them off but with nice paint on my truck cowl I really don't want to scratch it up just to remove the wiper arms.

So I got on "the Google" (again thanks W), typed in "Snap-on A192", typed in my credit card info, and now all I have to do is wait for the UPS man to deliver it for FREE.

In case anybody doesn't know, Snap-on stuff is usually made here and if all their internets

orders are the same the shipping is free.

If I could only get as excited over facebook.

bw4sale · 05-01-2009, 01:27 PM

Found this thread in the search feature. Just to clarify. The clip pushes UP? I can see a little tab handing down, but can't exactly tell what to do with it.

Legolas894 · 05-01-2009, 07:39 PM

Having the same problem-What do you push the clip up with? The tool looks great though.

Sinister · 05-01-2009, 08:51 PM

That Snap-on tool works great, $10 shipped, and worth every penny.

SFColbert · 05-02-2009, 12:43 AM

Towels on the cowl, a screwsriver to lever the clip away from the wiper arm post and PULL up.

Brad · 05-02-2009, 05:36 AM

Use anti-seize on the wiper arm knob threads before you go put it back on and it won't be as much of a problem the next time you need to take them off.

**Stocker** · 05-02-2009, 12:20 PM

Quote:

Originally Posted by ChevLoRay

NAPA also has a tool that is plier-like in that you squeeze the handles and lift the wiper off of the splined shaft. The tool has plasticized parts that protect both wiper and paint. As far as the one above is concerned, I've never seen one like that.....not saying it doesn't work, I just haven't seen one.

The tool, at NAPA, that I'm talking about is somewhere around $10, if my memory doesn't leave me stupid.

Not sure where I got mine years ago, but it works well....

02-17-2009, 06:03 PM	#1
6600DURAMAX Registered User Join Date: Nov 2000 Location: Wheatfield IN, USA Posts: 1,124	Wiper removal not going well AAAGGHHHGGAAAHHHH WIPERS will not come off – Had to remove the front clip with the cowl in place!! I know the little clip gets pushed up then the wiper should slide off but it is not working!!! I need them off without doing any more damage to the front clip or cowl. Any tips – I might just have to take a sawzall to the top of them and buy new ones???? thanks guys __________________ 1972 K5 - LS3/408 (595Hp) -6L80e-One Tons with 4.56, 20'' Beadlocks with 37'' rubber, full TMI interior, JL Audio ..... 1971 CREWMAX Build.....at body shop for couple more years

02-17-2009, 06:16 PM	#2
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: Wiper removal not going well Go to napa and buy this handy dandy tool and it will come right off. __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

02-17-2009, 06:17 PM	#3
67/72junkie Account Suspended Join Date: Oct 2002 Location: NC Posts: 1,129	Re: Wiper removal not going well You need a couple of pieces of scrape leather or old shoe to pad the cowl and protect from damage.2 large ,about 1/2 to 5/8 wide flat screw drivers.1 on each side twisted up with eqaul pressure usually pops them right off.

02-17-2009, 06:23 PM	#4
Botietruck '71 chevy s.bed/s.side Join Date: Mar 2005 Location: Chesapeake, VA Posts: 1,571	Re: Wiper removal not going well I took a bondo spreader and cut a semi-circle out of the thin tapered edge. It slips right around the shaft and protects the paint. __________________ STILL PLAYS WITH CARS...AND TRUCKS!! Parents! Be good to your kids...they get to choose your nursing home! 250 I-6 with a 3 speed Saginaw and Borg Warner Overdrive...She's got overdrive!

02-17-2009, 06:28 PM	#5
jsbgump Gone Fishing Join Date: Aug 2005 Location: Fort Worth, Texas 76135 Posts: 12,361	Re: Wiper removal not going well I guess i need to find the nearest napa to me. I can't find the tool on there website __________________ 68 Chevy Short Fleetside LSX Swap Under Way 3.73 posi 2.5/4 drop Frame of resto has been started 2022 Hyundai Tucson Limited 2019 Chevy Traverse Redline Edition Wifes Ride Build Thread http://67-72chevytrucks.com/vboard/s...=1#post3483616

02-17-2009, 06:37 PM	#6
thirdstreettito Resident of Here Join Date: May 2008 Location: Wesley Chapel, FL, USA Posts: 7,716	Re: Wiper removal not going well I undid the clip, then grabbed with pliers and pulled VERY hard. __________________ ~Bradley~ 2004 Black GTO LS2/T56 too much to list Miss having a truck

02-17-2009, 08:34 PM	#7
ChevLoRay Old Skool Club Join Date: Jun 2001 Location: Benton, AR "The Heart of Arkansas" Posts: 10,880	Re: Wiper removal not going well NAPA also has a tool that is plier-like in that you squeeze the handles and lift the wiper off of the splined shaft. The tool has plasticized parts that protect both wiper and paint. As far as the one above is concerned, I've never seen one like that.....not saying it doesn't work, I just haven't seen one. The tool, at NAPA, that I'm talking about is somewhere around $10, if my memory doesn't leave me stupid. __________________ Member Nr. 2770 '96 GMC Sportside; 4.3/SLT - Daily driven....constantly needs washed. '69 C-10 SWB; 350/TH400 - in limbo The older I get, the better I was.

02-17-2009, 09:52 PM	#8
chevy_mike Never Ending Projects Join Date: Jul 2006 Location: San Diego, CA Posts: 3,836	Re: Wiper removal not going well On my last '68, I had to cut one of them off. Even with the clip removed, it would not budge. Cut off wheel and it was done. I was replacing the arms anyways so I had nothing to loose and did not want to screw up the splined part. Good luck! __________________ . 1965 C10 Panel, Tiki Express http://www.67-72chevytrucks.com/vboa...d.php?t=506580 SOLD 1968 Chevy C10, Long, Fleetside, Hot Rod Hauler http://67-72chevytrucks.com/vboard/s...d.php?t=313233 SOLD 1965 Chevy C10, Long, Fleetside, Hot Rod C10 http://67-72chevytrucks.com/vboard/s...d.php?t=415702 SOLD We were given two ears and one mouth for a reason... listen twice as much and speak half as often...

02-17-2009, 11:29 PM	#9
6600DURAMAX Registered User Join Date: Nov 2000 Location: Wheatfield IN, USA Posts: 1,124	Re: Wiper removal not going well Thanks guys, I will go and get a tool and try it if not I will use a cutoff wheel (better that my idea of a sawzall) thanks guys - once again this site is Great __________________ 1972 K5 - LS3/408 (595Hp) -6L80e-One Tons with 4.56, 20'' Beadlocks with 37'' rubber, full TMI interior, JL Audio ..... 1971 CREWMAX Build.....at body shop for couple more years

02-17-2009, 11:40 PM	#10
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Wiper removal not going well some times things slide better when lubricated __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

02-18-2009, 12:35 AM	#12
Yellow67C10 Registered User Join Date: Sep 2008 Location: Vancouver, Washington Posts: 7	Re: Wiper removal not going well Perfect timing on this thread. I am trying toremove the wiper arms on our 1957 Belair and found the same problem..........Now thanks to everyone her I've found the answer to how do this. Thanks everyone.

02-18-2009, 02:27 PM	#13
mrein3 Registered User Join Date: Feb 2000 Location: Center City, MN, USA Posts: 3,253	Re: Wiper removal not going well I love the "internets" (as our former President once said). I have always had a hard time removing wiper arms. I've always got them off but with nice paint on my truck cowl I really don't want to scratch it up just to remove the wiper arms. So I got on "the Google" (again thanks W), typed in "Snap-on A192", typed in my credit card info, and now all I have to do is wait for the UPS man to deliver it for FREE. In case anybody doesn't know, Snap-on stuff is usually made here and if all their internets orders are the same the shipping is free. If I could only get as excited over facebook. __________________ '70 cab, '71 chassis, 383, TH350, NP205. '71 Malibu convertible '72 Malibu hard top Center City, MN

05-01-2009, 01:27 PM	#14
bw4sale Registered User Join Date: Sep 2006 Location: Hendersonville, TN Posts: 1,528	Re: Wiper removal not going well Found this thread in the search feature. Just to clarify. The clip pushes UP? I can see a little tab handing down, but can't exactly tell what to do with it. __________________ BRENT -'68 Stepside Project -'98 Z71 Daily Driver -Enough extra parts to build another truck and a half

05-01-2009, 07:39 PM	#15
Legolas894 Chemist under the hood... Join Date: Apr 2009 Location: Fort Erie,ON, Canada Posts: 617	Re: Wiper removal not going well Having the same problem-What do you push the clip up with? The tool looks great though. __________________ Current fleet: 2013 GMC Sierra, 5.3L, 4x4 1988 GMC Sierra, 305, Auto 1984 Jeep Grand Wagoneer, 360 V8 1997 VW Cabrio, 2.0L 2017 Toyota Rav4, 2.5L Stuff I wish I still had: 2013 Toyota Matrix [RIP] 1967 GMC 910 Fleetside, 283 V8 [1st Love-SOLD] 1987 Jeep Cherokee Laredo 4X4, 4.0 I-6 [SOLD} 1994 Chevrolet Caprice Classic, 5.7LV8 [SOLD] 1995 Chevrolet Astro AWD, 4.3L V6 (RIP) 1998 Chevrolet Suburban 4x4, 5.7L V8 [SOLD]

05-01-2009, 08:51 PM	#16
Sinister Between Trucks... Join Date: Mar 2002 Location: Los Angeles, CA. Posts: 3,830	Re: Wiper removal not going well That Snap-on tool works great, $10 shipped, and worth every penny. __________________ Beat it to fit, Paint it to match...



Register or Log In To remove these advertisements.

05-02-2009, 12:43 AM	#17
SFColbert Registered User Join Date: May 2005 Location: Escalon, CA Posts: 3	Re: Wiper removal not going well Towels on the cowl, a screwsriver to lever the clip away from the wiper arm post and PULL up.

05-02-2009, 05:36 AM	#18
Brad Out of the carpool lane. Join Date: Jan 2000 Location: Clark Co, WA Posts: 5,673	Re: Wiper removal not going well Use anti-seize on the wiper arm knob threads before you go put it back on and it won't be as much of a problem the next time you need to take them off. __________________ 1968 C-10 SWB, 5.7 Vortec/700R4/3.73 posi, Torch Red 1968 Camaro, 250/Powerglide, all original (No, I'm not gonna drop a 350 in it!...Jeez!) 2000 Honda VFR in the faster yellow! 2008 Husqvarna TE-610 1967 C-10 SWB 'Six Appeal'-Gone but not forgotten...

Register or Log In To remove these advertisements.