![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
![]()
ok... there's more to it than just trying to mock see ten... although, I will admit to wanting to be like him if I grow up.
I was finally able to get the tranny out of the burb... *cell pic* ![]() And even though the fluid it's bleeding in the above pic (and all in the back of the longhorn) is red.... don't let it fool you. ![]() The sludge in the bottom of the ban was not red. There was chunks of clutch in there. I *hope* to get a chance to run it over to Mr Bill the tranny guy this week. Then again, the tranny actually came out LAST sunday, and I've been saying I hope to get a chance all friggen week. To say it was cold in there is an understatement. I can't remember the actual temp, but I know it dropped about 15 to 20 degrees from when I got there till the time I left. ![]() I plan on fine tuning the drop while it is laid up. I want to bring the front down a bit more, and firm up the rear... or raise the rear a tad. Right now it sits higher up front, and the rear axle slams into the frame when you even consider hitting a ciggarette butt in the road. So some trimming on the coils in front, and some helper in-the-coil type air bags in back should do the trick. it needs a C notch... but I'm not ready to commit to that quite yet. Plus, i can't weld to save my life. So I leave my baby up on jackstands at all 4 corners, and tires in the back room stacked up. ![]() As I head out the door and hit the lights... I have an idea... sure, it's a direct rip off of see ten's efforts... but, in all honesty, it's one I've wanted to do for a long time now. ![]() There's a shop we deal with all the time at work, there garage is actually a very old church that was converted to a shop in the 20's acording to the guys who work there. It's all very old brick, and rooms built out of wooden planks... I'd love to take good pics of the joint, but there is a key board inside the office there that I want to own real bad. *cell phone pic again* ![]() So some of you remember the thread about my buddy's new K/20 cheyenne... http://67-72chevytrucks.com/vboard/s...d.php?t=329823 Well, I got a couple more pics of it.... the requested SPID shot... ![]() And the ORIGINAL title... look at the dates on this. I don't even know if the state of Oregon still has titles that look like this. Heck, look when it was signed over by the original owner and his wife.... back in 86! ![]() ![]() |
![]() |
![]() |
![]() |
#2 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: my lame attempt @ nice pics...
And then a few pics of the truck he got for parts.... 71 cheyenne C/10. He mostly wants the grill and core support for another 72 cheyenne he may be buying, the front bumper will go on the skunk, the rear slider window in the K/20, the 305 chevy that was in it has already been sold and delivered, then a few odds and ends here and there for his stuff.... the rest of it I hope to pick over, I hope to get the seat, some under dash A/C stuff and the front and rear complete suspentions. The tranny will probably get sold as a core, the cab and frame probably scrapped or sold off eventually.
![]() ![]() ![]() oh yeah... the stock tilt will go in the skunk too... ![]() ![]() Nothing else much goingon here sadly enough. ![]() i just wish it'd warm up a bit so we can get some friggen work done. |
![]() |
![]() |
![]() |
#3 |
Eat My Rust
Join Date: Jan 2007
Location: Cypress, Texas
Posts: 3,362
|
Re: my lame attempt @ nice pics...
![]() That just says it all. ![]() Last edited by texanidiot25; 03-01-2009 at 11:56 PM. |
![]() |
![]() |
![]() |
#4 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: my lame attempt @ nice pics...
the oil drum is actually my trash can now.
![]() |
![]() |
![]() |
![]() |
#5 |
BlahBlahBlah
Join Date: Feb 2002
Location: Wa.
Posts: 19,881
|
Re: my lame attempt @ nice pics...
Very cool pics...nicely done.
__________________
… … … … … … … … ... … … … … … … … … … … … |
![]() |
![]() |
![]() |
#6 |
Eat My Rust
Join Date: Jan 2007
Location: Cypress, Texas
Posts: 3,362
|
Re: my lame attempt @ nice pics...
Haha, I figure. My dad has a huge Penzoil one as well..
Seems like a sweet little shop besides the lack of heat. Too bad you aren't down south though. I'm sure you'd hate to hear that it was 65 all day, slightly windy. That was our sudden "Cold Front". I had on a T-shirt and jeans. Powder coatin' and wiring stuff on the CST10. Ah, the lack of a real winter is nice. Last edited by texanidiot25; 03-02-2009 at 12:01 AM. |
![]() |
![]() |
![]() |
#7 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: my lame attempt @ nice pics...
yeah... I hate you now.
![]() |
![]() |
![]() |
![]() |
#8 |
1 thing at a time is progress.
Join Date: Jun 2007
Location: Ball Ground GA
Posts: 5,511
|
Re: my lame attempt @ nice pics...
__________________
Alan
Philippians 2:14-16 |
![]() |
![]() |
![]() |
#9 |
Resident of Here
Join Date: May 2008
Location: Wesley Chapel, FL, USA
Posts: 7,716
|
Re: my lame attempt @ nice pics...
This pic describes everything we know and love about you Andy!
![]()
__________________
~Bradley~ 2004 Black GTO LS2/T56 too much to list ![]() Miss having a truck ![]() Last edited by thirdstreettito; 03-02-2009 at 12:18 AM. |
![]() |
![]() |
![]() |
#10 |
Hittin E-Z Street on Mud Tires
![]() Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: my lame attempt @ nice pics...
It snowed 3" here tonight... EVERYTHING is shut down.
Congrats on gettin' the tranny out! You'll be rollin' again in no time! This pic looks like the cover of a murder mystery book! ![]()
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride ![]() American Born, Country by the Grace of God ![]() 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! |
![]() |
![]() |
![]() |
#11 |
Saving 1 truck at a time!
Join Date: Aug 2001
Location: Kent, WA
Posts: 6,465
|
Re: my lame attempt @ nice pics...
Now that's some funny sh*!! there!
![]() ![]() ![]()
__________________
'68 C20 Longhorn 50th Anniversary 400/TH400 '68 C20 Longhorn 50th Anniversary 468/TH400w/buckets '72 C20 Halfhorn (Longhorn w/o cab and front clip) '69 Flxible Cruiser (look up ugly in the dictionary) |
![]() |
![]() |
![]() |
#12 |
Roadtrip!
![]() Join Date: Feb 2003
Location: Grand Rapids MN
Posts: 13,737
|
Re: my lame attempt @ nice pics...
Looks like you have a nice shop going there andy.
The pic of you in the burb reminds me of a deer in headlights.
__________________
67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto |
![]() |
![]() |
![]() |
#13 |
Designated Grumpy Old Man
![]() Join Date: Oct 2001
Location: arlington, washington usa
Posts: 3,092
|
Re: my lame attempt @ nice pics...
It maybe cold inside but it sure beats laying out in the snow doing a tranny removal. Nice to have a shop after all this time working outside isn't it.
![]()
__________________
Never let the truth get in the way of a good story 71 Chev 1/2 ton 4X4 LWB Fleetside SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=361222 http://www.youtube.com/watch?v=1LgREwtDfaA 68 Chev 1 ton flat bed http://www.youtube.com/watch?v=0bO8szzlD4A 56 Chev Handyman Wagon http://www.youtube.com/watch?v=9y-6ddpBTkM http://www.youtube.com/watch?v=lbLzZ7zY8wA 56 Chev Belair http://67-72chevytrucks.com/vboard/s...d.php?t=410667 http://www.youtube.com/watch?v=xoW0Ei7ZNIg |
![]() |
![]() |
![]() |
#14 | |
Senior Member
Join Date: Jul 2006
Location: Blountville, Tn.
Posts: 3,904
|
Re: my lame attempt @ nice pics...
Quote:
Nice pics, you'll have the burb up and running in no time.
__________________
*We could learn a lot from crayons... Some are sharp; some are pretty;and some are dull. Some have weird names; and all are different colours;but they all have to live in the same box. * You may be only one person in the world, But you may also be the world to one person. * Some mistakes are too much fun to only make once. Two rules in life. 1. Never sweat the small stuff! 2. Everything is small stuff! Last edited by BarryB; 03-02-2009 at 01:17 AM. |
|
![]() |
![]() |
![]() |
#15 |
Senior Member
![]() ![]() Join Date: Dec 1999
Location: Urbana,Ohio,USA
Posts: 4,618
|
Re: my lame attempt @ nice pics...
You need a Kewl Mt.Dew sign, metal or neon to hang on the wall. Maybe a Mt.Dew clock.
__________________
2008 Chevy HHR 1/2 panel. 1949 Chevy Panel truck(just sittin, waiting) Board member #6 |
![]() |
![]() |
![]() |
#16 |
Registered User
Join Date: Sep 2001
Location: Hacienda Heights, California USA
Posts: 474
|
Re: my lame attempt @ nice pics...
Nice photos, and like they said. At least you are working indoors. My driveway is steep, so taking the trans out will be interesting to say the least.
I can't do it in the street as a local deputy sheriff, has already had my el camino and the truck impounded once before. That was a $600 buck waisted, just to get my vehicles out of the impound yard. Both vehicles have current registration and are insured. As for our winter here in LaLaLand.... it was close to 80 degrees today, almost had to put a sweatshirt on ![]()
__________________
'72 GMC custom camper 350/350 Last edited by spinning wheels; 03-02-2009 at 02:50 AM. |
![]() |
![]() |
![]() |
#17 |
WTB this ad
Join Date: Sep 2004
Location: Lafayette Georgia
Posts: 5,074
|
Re: my lame attempt @ nice pics...
Cool pics brother! That parts truck interior has an interesting vibe to it....kinda a cross between funeral home and lowrider/bomba??? Roll with it!
![]() |
![]() |
![]() |
![]() |
#18 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: my lame attempt @ nice pics...
LOL! It's the same crap up on the headliner too.
![]() |
![]() |
![]() |
![]() |
#19 |
Registered User
Join Date: Feb 2007
Location: OHIO
Posts: 25
|
Re: my lame attempt @ nice pics...
congrats on the shop Andy, I might be interested in the front control arms on that parts truck if available
__________________
67 GMC, SWB, 472 Cadillac, Turbo 400, 273 rear |
![]() |
![]() |
![]() |
#20 | |
Registered User
Join Date: Apr 2002
Location: New Carlisle, Ohio,USA
Posts: 1,404
|
![]() Quote:
"Been drivin' all night, my hands wet on the wheel"
__________________
![]() ![]() ![]() LIFE AIN'T EASY WHEN YER FAT AND GREASY! GMC= Got More Class! ![]() ![]() Last edited by OhioDan; 03-02-2009 at 09:46 AM. |
|
![]() |
![]() |
![]() |
#21 |
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
Re: my lame attempt @ nice pics...
The pictures are cool, maybe not as cool as the temperature but cool.
The rear helper springs made a world of differance in the 71 ride. No more bottoming out. I had to call them and get some larger spacers though so the fittings would work.
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 ![]() Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
![]() |
![]() |
![]() |
#22 |
Special Order
![]() ![]() Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,858
|
Re: my lame attempt @ nice pics...
That dark shot is schweet.Those lame pictures are nice.
Outside sucks.Inside better.Concrete great! You need a propane heater to heat that place.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ Last edited by special-K; 03-02-2009 at 03:02 PM. |
![]() |
![]() |
![]() |
#23 |
Tonawanda 454
Join Date: Mar 2004
Location: Liquid Sunshine State
Posts: 2,755
|
Re: my lame attempt @ nice pics...
they need a better heater for that garage... and having the door open doesn't help...
great shots LHM
__________________
91 Chevy Suburban Tonawanda 454 R2500 - SOLD!!! ![]() 04 Dodge Durango 5.7L Hemi 2WD, 24K miles (as of July 2011) In the past 30 years about 90% of Fords are still on the road, the other 10% made it home. ------------------- |
![]() |
![]() |
![]() |
#24 |
Registered User
Join Date: Apr 2008
Location: Angleton, TX
Posts: 2,219
|
Re: my lame attempt @ nice pics...
I agree with what was said before, cold and a shop beats warm and no shop. Yeah it has been in the 70's and 80s in central/ southern Texas the last few weeks, but it still sucks when I have to work on my burb in my gravel driveway. Tools and small fittings getting lost in the grass, and soon it will be so hot out that I won't be able to touch any sheetmetal while working on my truck without getting a 3rd degree burn.
|
![]() |
![]() |
![]() |
#25 | |
Hittin E-Z Street on Mud Tires
![]() Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: my lame attempt @ nice pics...
Quote:
![]()
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride ![]() American Born, Country by the Grace of God ![]() 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! |
|
![]() |
![]() |
![]() |
Bookmarks |
|
|