![]() |
![]() |
#1 |
Registered User
Join Date: Jul 2008
Location: Vancouver BC
Posts: 448
|
Newer truck seats
Hey,
Anyone out there using newer tahoe/suburban/silverado/sierra/denali seats? the bench with the middle seat/arm rest. Any modifications needed? does it use the original bolt holes? Thanks
__________________
1978 GMC Jimmy 454bbc Turbo400 NP205 3.73 gears 4inch lift 33's |
![]() |
![]() |
![]() |
#2 |
Special Order
![]() ![]() Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,859
|
Re: Newer truck seats
I`ve seen them used.Not sure about the bolt-up.I hear some say it cramps the cab due to the "fullness" of the seats.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
![]() |
![]() |
![]() |
#3 |
Junior Member
Join Date: Dec 2006
Location: Southeast Missouri
Posts: 2,436
|
Re: Newer truck seats
I guess it has been about 10years ago I put a 60/40 split seat out of a '92 GMC in a '72 Chevy truck and it fit ok, but did require drilling a few more holes. Where I drilled the holes I put a plate metal underneath the cab to strenghten the floor.
That year seat was not of the overstuffed type like some of the newer years. Dannny
__________________
'67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E. |
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: Jan 2006
Location: Peyton, CO
Posts: 448
|
Re: Newer truck seats
I've used 90s style seats in a couple of 67 -72 trucks. I've used some of the existing holes then drilled through the floor for the remaining bolts. One thing highly recommended (such as by ShyGuy) is to plate/reinforce the floor when drilling holes in a new location to accommodate the newer (or any, for that matter) seats. I like to sit fairly close to the wheel, probably helped along by my 5' 3" wife, so I wasn't uncomfortable. One truck I recently sold (my avatar) to a friend and he is planning to replace the seat due to insufficient "space" for him.
__________________
don "The DRBMan" 2014 Audi A4 (The Wife's Daily Driver) 2017 HD Ultra (The Cruiser) 2003 HD Fatboy (The Ride) 2001 Chevy Suburban (Another back up!!) For the first time in forever, not a single 67-72 Chevy truck, Blazer, or Suburban on the property! Basically retired and getting the new Motorhome ready for some traveling. Doing a bit of work on the house getting it ready to sell! LOL!! |
![]() |
![]() |
![]() |
#5 |
Registered User
![]() Join Date: Dec 2008
Location: eufaula,alabama
Posts: 198
|
Re: Newer truck seats
I am in the process of installing 40/20/40 seats from a 2001 gmc truck in my 68. The 01 seats seem to fit better on a flat floor. This allowed me to install the fixed center section further back without hitting the back of the cab when tilted up. I cut out the raised floor section (where the front original seat mounts are). Then welded in new flat metal and will install 3/16 plate on the bottom of the flat area for strength. I feel this needs to be plenty strong because These seats have the seat belts in them. Not a hard modification, like most things it takes time.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|