![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Sep 2009
Location: ringgold, ga
Posts: 164
|
Clutch and pressure plate question??
I am removing the saginaw three speed and replacing it with a t5 out of an s10. i have to replace the clutch, but my question is, is it possible to remove the clutch by loosening the pressure plate and slipping the clutch out and slipping the new one back in? can i bypass taking the bell housing off?
__________________
70 Chevy C10, LT1, T5, "Blue Beast" |
![]() |
![]() |
![]() |
#2 | |
The Older Generation
![]() ![]() ![]() Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,519
|
Re: Clutch and pressure plate question??
Quote:
It's been a while since I've had one apart but it seems to me that you can, but you have to turn the motor over to get all of the bolts out of the pressure plate. I would recommend turning it over by hand with a small pry bar on the teeth of the flywheel instead of using the starter. Do you have the adapter plate for the swap? LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Sep 2009
Location: ringgold, ga
Posts: 164
|
Re: Clutch and pressure plate question??
ok. i tried only taking about 4 bolts out, guess i should take the rest out. adapter plate? what do you mean? as far as i know, ive changed the spline, bolt pattern is the same, it should bolt up
__________________
70 Chevy C10, LT1, T5, "Blue Beast" |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Sep 2009
Location: ringgold, ga
Posts: 164
|
Re: Clutch and pressure plate question??
Ttt
__________________
70 Chevy C10, LT1, T5, "Blue Beast" |
![]() |
![]() |
![]() |
#5 | |
The Older Generation
![]() ![]() ![]() Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,519
|
Re: Clutch and pressure plate question??
Quote:
You mean that you changed the input shaft to a shorter one? LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Sep 2009
Location: ringgold, ga
Posts: 164
|
Re: Clutch and pressure plate question??
Not quite. Just used a shaft out of a t5 that has been behind a 350 previously. So the splines are cut longer, collar is cut a little etc. All the work was done by a local transmission shop.
__________________
70 Chevy C10, LT1, T5, "Blue Beast" |
![]() |
![]() |
![]() |
#7 | |
The Older Generation
![]() ![]() ![]() Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,519
|
Re: Clutch and pressure plate question??
Quote:
You should be good to go then. I just bought a 9/16" spacer plate for mine. LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Sep 2009
Location: ringgold, ga
Posts: 164
|
Re: Clutch and pressure plate question??
Alright. Thanks for your help, greatley appericated.
Marshall
__________________
70 Chevy C10, LT1, T5, "Blue Beast" |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Jun 2007
Location: Edmonton, Alberta
Posts: 423
|
Re: Clutch and pressure plate question??
Yeh you can just slip the clutch and pressure plate out the inspection hole. I did EXACTLY this this weekend for the EXACT same reason(sag 3spd to t-5 swap).
|
![]() |
![]() |
![]() |
Bookmarks |
|
|