NH Blueprinted and Balanced 383 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**CUSTOM/10** · 04-23-2010, 11:43 AM

SELLING THIS FOR A FRIEND !!!

Started with a 1989 seasoned truck 350 block, 4 bolt main, 1 piece seal, full roller cam shaft. Block was completely done over by Golen Machine (clearanced for the crank, magnafluxed, shotpeened and cam bearings install). Add a forged 383 Callies 4340 forged (chrome-moly) crank, forged 4340 H-beam connecting rods and and forged + coated 8.9:1 pistons (for turbo or blower). All balanced to zero.
GM "Hot Cam" with new roller lifters and the appropriate valve springs
GM Vortec "Fast Burn" aluminum heads
Melling high performance oil pump
SCE Copper cored head gaskets.
Jesel Shaft Mounted roller rockers in stainless.
Pete Jackson "noisy" gear drive
All aluminum tin - Valve covers, timing chain cover, etc.

Not a single item in this engine is used but for the block itself. It has never been fired since assembly.

It currently has a Edelbrock Air Gap 4150 style intake on it.

I built three of these, 2 with iron Vortec heads. This one I built for my GMC truck so it got a little extra attention..

$3,000 - priced for a very fast sale. There's more then that in the valve train alone.

I can include a Barry Grant King Demon currently set up for 750CFM with the complete tuning kit for another 500.00.

I also have a Ramjet 350 intake that could go with this for an additional 600.00. + the Edelbrock Air Gap. Includes all the sensors on the intake. I also have mechanical (the block will drive one) and electric fuel pumps that could go with it.

This is better than a GMPP "Fastburn 383" for 2K less, includes an intake. They advertise theirs at 425HP. This one comes with forged rods, no powdered metal here. Will handle nitrous, a blower or turbos all day long, until about 900hp...

Here's a link to a FastBurn 383:
http://www.gmperformanceparts.com/En...8772&engCat=sb

Gary

rlm316 · 04-24-2010, 06:06 AM

ttt for a good deal

**CUSTOM/10** · 04-25-2010, 08:25 AM

Ttt

**CUSTOM/10** · 05-03-2010, 06:55 PM

ttt

boonedogs72 · 05-03-2010, 11:10 PM

would he be interested in any big block stuff?

**CUSTOM/10** · 05-05-2010, 07:37 PM

He isn't looking for any Motor parts but is looking for a SWB fleet bed or bed floor also a nice GMC grille and will take that in partial trade !

oldblue1968chevy · 05-05-2010, 07:45 PM

I wish you were closer!!!!!!

Southern C10 · 05-05-2010, 09:32 PM

Quote:

Originally Posted by CUSTOM/10

He isn't looking for any Motor parts but is looking for a SWB fleet bed or bed floor also a nice GMC grille and will take that in partial trade !

How about a very nice SWB step bed? Its in my Build thread.

**CUSTOM/10** · 05-06-2010, 07:52 AM

He's not interested in steps sides. He is interested in chasis components, 2wd lower suspension parts.

He can deliver to TN for $300...

Southern C10 · 05-06-2010, 07:58 AM

Quote:

Originally Posted by CUSTOM/10

He's not interested in steps sides. He is interested in chasis components, 2wd lower suspension parts.

He can deliver to TN for $300...

My brother is looking for a motor. I will pass this to him and let you know.

**CUSTOM/10** · 05-06-2010, 08:09 AM

This is a heck of a motor for the money, he has around $5,000 into it.

I'm get one of his more mildly done 383's

**CUSTOM/10** · 05-09-2010, 02:39 PM

ttt

**CUSTOM/10** · 05-19-2010, 05:14 PM

Ttt

04-23-2010, 11:43 AM	#1
CUSTOM/10 Senior Member Join Date: May 2003 Location: Sandown, NH Posts: 2,833	Blueprinted and Balanced 383 SELLING THIS FOR A FRIEND !!! Started with a 1989 seasoned truck 350 block, 4 bolt main, 1 piece seal, full roller cam shaft. Block was completely done over by Golen Machine (clearanced for the crank, magnafluxed, shotpeened and cam bearings install). Add a forged 383 Callies 4340 forged (chrome-moly) crank, forged 4340 H-beam connecting rods and and forged + coated 8.9:1 pistons (for turbo or blower). All balanced to zero. GM "Hot Cam" with new roller lifters and the appropriate valve springs GM Vortec "Fast Burn" aluminum heads Melling high performance oil pump SCE Copper cored head gaskets. Jesel Shaft Mounted roller rockers in stainless. Pete Jackson "noisy" gear drive All aluminum tin - Valve covers, timing chain cover, etc. Not a single item in this engine is used but for the block itself. It has never been fired since assembly. It currently has a Edelbrock Air Gap 4150 style intake on it. I built three of these, 2 with iron Vortec heads. This one I built for my GMC truck so it got a little extra attention.. $3,000 - priced for a very fast sale. There's more then that in the valve train alone. I can include a Barry Grant King Demon currently set up for 750CFM with the complete tuning kit for another 500.00. I also have a Ramjet 350 intake that could go with this for an additional 600.00. + the Edelbrock Air Gap. Includes all the sensors on the intake. I also have mechanical (the block will drive one) and electric fuel pumps that could go with it. This is better than a GMPP "Fastburn 383" for 2K less, includes an intake. They advertise theirs at 425HP. This one comes with forged rods, no powdered metal here. Will handle nitrous, a blower or turbos all day long, until about 900hp... Here's a link to a FastBurn 383: http://www.gmperformanceparts.com/En...8772&engCat=sb Gary Attached Images __________________ Gary 72 SWB 4x4 My 72 SWB Build http://67-72chevytrucks.com/vboard/s...d.php?t=259859 Last edited by CUSTOM/10; 04-23-2010 at 11:44 AM.

04-24-2010, 06:06 AM	#2
rlm316 Registered User Join Date: Aug 2006 Location: Woodstown, NJ Posts: 669	Re: Blueprinted and Balanced 383 ttt for a good deal

04-25-2010, 08:25 AM	#3
CUSTOM/10 Senior Member Join Date: May 2003 Location: Sandown, NH Posts: 2,833	Re: Blueprinted and Balanced 383 Ttt __________________ Gary 72 SWB 4x4 My 72 SWB Build http://67-72chevytrucks.com/vboard/s...d.php?t=259859

05-03-2010, 06:55 PM	#4
CUSTOM/10 Senior Member Join Date: May 2003 Location: Sandown, NH Posts: 2,833	Re: Blueprinted and Balanced 383 ttt __________________ Gary 72 SWB 4x4 My 72 SWB Build http://67-72chevytrucks.com/vboard/s...d.php?t=259859

05-03-2010, 11:10 PM	#5
boonedogs72 Registered User Join Date: Apr 2005 Location: redding ca Posts: 1,438	Re: Blueprinted and Balanced 383 would he be interested in any big block stuff?

05-05-2010, 07:37 PM	#6
CUSTOM/10 Senior Member Join Date: May 2003 Location: Sandown, NH Posts: 2,833	Re: Blueprinted and Balanced 383 He isn't looking for any Motor parts but is looking for a SWB fleet bed or bed floor also a nice GMC grille and will take that in partial trade ! __________________ Gary 72 SWB 4x4 My 72 SWB Build http://67-72chevytrucks.com/vboard/s...d.php?t=259859 Last edited by CUSTOM/10; 05-05-2010 at 07:39 PM.

05-05-2010, 07:45 PM	#7
oldblue1968chevy Grandpa in the rustmobile... Join Date: Nov 2008 Location: Spokane WA/Viola TN Posts: 11,422	Re: Blueprinted and Balanced 383 I wish you were closer!!!!!! __________________ John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4

05-06-2010, 07:52 AM	#9
CUSTOM/10 Senior Member Join Date: May 2003 Location: Sandown, NH Posts: 2,833	Re: Blueprinted and Balanced 383 He's not interested in steps sides. He is interested in chasis components, 2wd lower suspension parts. He can deliver to TN for $300... __________________ Gary 72 SWB 4x4 My 72 SWB Build http://67-72chevytrucks.com/vboard/s...d.php?t=259859

05-06-2010, 08:09 AM	#11
CUSTOM/10 Senior Member Join Date: May 2003 Location: Sandown, NH Posts: 2,833	Re: Blueprinted and Balanced 383 This is a heck of a motor for the money, he has around $5,000 into it. I'm get one of his more mildly done 383's __________________ Gary 72 SWB 4x4 My 72 SWB Build http://67-72chevytrucks.com/vboard/s...d.php?t=259859

05-09-2010, 02:39 PM	#12
CUSTOM/10 Senior Member Join Date: May 2003 Location: Sandown, NH Posts: 2,833	Re: Blueprinted and Balanced 383 ttt __________________ Gary 72 SWB 4x4 My 72 SWB Build http://67-72chevytrucks.com/vboard/s...d.php?t=259859

05-19-2010, 05:14 PM	#13
CUSTOM/10 Senior Member Join Date: May 2003 Location: Sandown, NH Posts: 2,833	Re: Blueprinted and Balanced 383 Ttt __________________ Gary 72 SWB 4x4 My 72 SWB Build http://67-72chevytrucks.com/vboard/s...d.php?t=259859



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.