anybody have pics of bagged stock bed floor, arms, x-member etc?

[cochino12]

I posted this in the suspension board a while back but didnt really have any luck so I thought I would try here.

Does anyone have pictures of the truck/blazer with just drop spindles and bags, simple 4 link rear and stock floor? Everyone seems really concerned with laying frame and thats really all I find while searching for pictures. Thanks

[54Caddy]

I want to know the same also.. anyone out there like us that have done this..

[thrtsxchambers]

I have drop spindles, bagged and stock floor(as far as no body drop). My bed floor has been raised but has nothing to do with the air ride. If you mean stock floor as no hole in the bed floor then I know there are a few on here that may post soon and that would require a c notch instead of a step notch.
just to clear this up, the heading states stock bed floor but the post says stock floor. I do think you mean the bed floor to be stock correct? The posting could be missunderstood to be stock floor body drop.
just making sure I and maybe others understand the question.

[Driveway Dreams]

Yes, he is wanting to see some that are aired out without being "all cut up". How low can you lay out with out changing any part of the floor?

[gcwhite]

Mine has some lowered lower control arms,factory spindles and a four link. Didn't cut or remove any body.

[SCOTI]

N2TRUX's 77 would fit that description....

[classicchev]

Sounds exactly like your old crew cab. With your 20's I can set the crossmember on the garage floor and Im way inside the inner lip on the fender. Rear has the Air Bar, and will not go any lower than the c-notch. But Im still not going to post a pic.

Someday when its done I might.

[andrewmp6]

Look at http://ridetechgarage.com/more/1986-chevy-truck/

[blazer2007]

gcwhite-what did you use for a 4 link,custom made or store bough,I,m trying to decide on one for mine.Mine is flipped with a 1 in spacerer and spindles,cut 1 coil and bags,no cups

[Captkaos]

N2TRUX before and now setup is just like you described.

[54Caddy]

n2Trux lets get something on here about yours ive seen pictures but want to know more where are you man

[cochino12]

Kens truck isnt the best example because it could still go lower if he still removed his inner fenders, and if I remember correctly he also wanted it to be able to roll when aired out (in case of a broken line, or bag).

[cochino12]

Originally Posted by andrewmp6

Look at http://ridetechgarage.com/more/1986-chevy-truck/

Thanks for the link!! Doesnt seem like that get very low? Mine is lower than that now if those are 20" wheels/tires.

[N2TRUX]

Best I can do is this.

[54Caddy]

come on explain what you have.. dont just leave us hanging drolling over that clean blazer. Damn lucky guy has all yellow 77 trim on his truck now one clean ass blazer. I found me a yellow tailgate band to go with my cab band now N2trux. Just need some fender moldings.

[Captkaos]

His front has AirRides bag kit and spindles, the rear has AirRide Triangulated 4 link with a C-notch.

I was thinking you were wanting truck pics.... His pickup with the front AirRioe bags and Air over leaf was as close to stock and dropped as you can get.

[Pullin81]

heres mine...3 inch drop spindles and a paralelle 4 link and small c notch.....

[cochino12]

Originally Posted by N2TRUX

Best I can do is this.

Ken, in the rear did your axle bump the tub or the c-notch first?

[N2TRUX]

Originally Posted by 54Caddy

come on explain what you have.. dont just leave us hanging drooling over that clean blazer....

Unfortunately I no longer own that Blazer. After many attempts to find a shop that would finish it failed, I finally sold it.

Originally Posted by cochino12

Ken, in the rear did your axle bump the tub or the c-notch first?

Adam it actually did both at about the same time. We had the short flat stops in the notch, and the pumpkin would barely bump the pan when aired out.

[classicchev]

Originally Posted by Pullin81

heres mine...3 inch drop spindles and a paralelle 4 link and small c notch.....

Cool, another Calgary guy!!!!

Keeping the early clip?? Have a 90 available, I may have some interior stuff for you from a 90 Sub. Need any parts?

Darren

[justpball]

here is my burb and this is with the simple setup, when i first done it... so it is just like you are looking for... lmk if you have any questions

[cochino12]

Originally Posted by justpball

here is my burb and this is with the simple setup, when i first done it... so it is just like you are looking for... lmk if you have any questions

I've been comparing your's to others that I've seen with a stock floor and it looks like your rear goes a lot lower? Does a 10 bolt have that much smaller of a pumpkin? Is the notch on yours bigger than most? Any ideas ?

[justpball]

i dont know, my chunk hits the floor, axle hits top of the notch and tires just touch the inner fenders all at the same time, so if i had 22s it would not go as low... so I dont know.