![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Apr 2010
Location: Beaumont, Texas
Posts: 136
|
Pre-fab front wheel tubs?
Hey does anyone know where I can buy front wheel tubs for my bagged 86 c10? I've seen them made to order for the bed but not the front. Can you guys help me out? Thanks!
Posted via Mobile Device |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Mar 2004
Location: SWANTON OHIO
Posts: 114
|
Re: Pre-fab front wheel tubs?
Suicidedoors,has some.
__________________
81 blazer 2wd tukin 30's 07 Jeep Grand Cherokee on 26's Tube chassis 5.3,dual T cases,54" boggers,steering rocks Dodge 3500 with some mods |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jan 2007
Location: connecticut
Posts: 127
|
Re: Pre-fab front wheel tubs?
trailer fenders
![]() |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Apr 2010
Location: Beaumont, Texas
Posts: 136
|
Re: Pre-fab front wheel tubs?
Thanks....I checked out the ones on ***************** but its hard to get a visual of what they look like installed. Does anyone here have a pic of some installed or a pic of the trailer fenders installed. And what's y'all opinion as far as looks.......which do y'all perfer?
Posted via Mobile Device |
![]() |
![]() |
![]() |
#5 | |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,982
|
Re: Pre-fab front wheel tubs?
Quote:
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Apr 2010
Location: Beaumont, Texas
Posts: 136
|
Re: Pre-fab front wheel tubs?
I don't know what I would perfer beings I have never had either one and only seen the trailer fenders once in a picture.......that's the whole reason I made this post. So like I said any pictures and info would be very helpful!!
Posted via Mobile Device |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jan 2007
Location: connecticut
Posts: 127
|
Re: Pre-fab front wheel tubs?
first picture is a first gen s 10 i did and the second is a dual axle fender cut in half on a colorado that im workin on. the round fenters are about $22 each and the dual about $60 . You can get em at pretty much any where trailers are sold or fixed
![]() ![]() |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Mar 2004
Location: SWANTON OHIO
Posts: 114
|
Re: Pre-fab front wheel tubs?
I was talking about the firewall tubs,.my BAD.
__________________
81 blazer 2wd tukin 30's 07 Jeep Grand Cherokee on 26's Tube chassis 5.3,dual T cases,54" boggers,steering rocks Dodge 3500 with some mods |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Jan 2007
Location: vernon b.c.
Posts: 3,022
|
Re: Pre-fab front wheel tubs?
I,ve been trying to decide myself which way to go but here are some pics I,ve saved
|
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Jan 2007
Location: connecticut
Posts: 127
|
Re: Pre-fab front wheel tubs?
Then get one of the round trailer fenders cut it in half put it in the fire wall cut off what you dont need of the tub half then patch the inner side, or the side closest to the center of the truck. hate to direct any one away from this site but check out s10forum.com tons of info on that site
Last edited by mullit; 09-14-2010 at 07:35 PM. |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Apr 2010
Location: Beaumont, Texas
Posts: 136
|
Re: Pre-fab front wheel tubs?
Thanks for the help guys. Now what size would I need if I'm going to run 22's? I would assume a 8 or 9 inch wide but there different sizes in height and length as well, which I'm pretty sure y'all know. So what's best???
Posted via Mobile Device |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Jan 2008
Location: HOUSTON TX
Posts: 1,161
|
Re: Pre-fab front wheel tubs?
this is how i built my inners for my dually project.....
![]() |
![]() |
![]() |
![]() |
Bookmarks |
|
|