200R4 Swap ? - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BHyatt · 09-23-2010, 09:59 PM

Big thing I noticed was the view looking down around the motor to the ground with the hood up. The 2004R is a lot narrower than the TH350.

68GMCCustom · 09-23-2010, 11:50 PM

Got mine mounted up and bolted in the rear position. Drive shaft is a bit further into the trans then I want....but then again I haven't got the rear end exactly where it needs to be.

oh....and I came across this diagram of a 200-4r the other day.

current drive shaft position:

Mondo · 09-24-2010, 06:13 PM

I've had one in my 67 for a couple years now. The only issue I have is that it won't kick down out of lock up until there's a lot of throttle (or tap the brakes but it goes right back into 4th). It's a pain when in 30-45mph traffic as it lugs the motor. I've been to 3 tranny shops for adjustments but it hasn't worked out.
My solution was to put in a small dash toggle switch connected to the brake switch sensor and switch off the lock out when cruising around town (back to basically a turbo 350).
Do you guys have any problem with it releasing 4th gear lock up at a reasonable throttle position? Maybe I should continue my search for a tranny swap expert.

ebfabman · 09-24-2010, 06:33 PM

I only use the lockup over 60mph.

68GMCCustom · 09-24-2010, 07:04 PM

Quote:

Originally Posted by Mondo

I've had one in my 67 for a couple years now. The only issue I have is that it won't kick down out of lock up until there's a lot of throttle (or tap the brakes but it goes right back into 4th). It's a pain when in 30-45mph traffic as it lugs the motor. I've been to 3 tranny shops for adjustments but it hasn't worked out.
My solution was to put in a small dash toggle switch connected to the brake switch sensor and switch off the lock out when cruising around town (back to basically a turbo 350).
Do you guys have any problem with it releasing 4th gear lock up at a reasonable throttle position? Maybe I should continue my search for a tranny swap expert.

for a 200-4r only one name comes to mind....Art Carr.....California Performance Transmissions. http://www.cpttransmission.com/

**19702wdc10** · 09-04-2013, 08:41 AM

Quote:

Originally Posted by ebfabman

I only use the lockup over 60mph.

I am looking to put a 200 r4 behind a chevy 250 3 speed also and was wondering what flexplate and torque converter you are using?
Thanks
Joe
Posted via Mobile Device

C10_ustacould · 12-17-2013, 06:59 PM

I would also like more info on installing a 200-4r behind a 250 I6, has anyone done more research since 2010?

09-23-2010, 09:59 PM	#26
BHyatt Registered User Join Date: Jul 2007 Location: New Castle, IN Posts: 199	Re: 200R4 Swap ? Big thing I noticed was the view looking down around the motor to the ground with the hood up. The 2004R is a lot narrower than the TH350.

09-23-2010, 11:50 PM	#27
68GMCCustom Truck and auto performance nut Join Date: Feb 2007 Location: McKinney,Texas Posts: 3,848	Re: 200R4 Swap ? Got mine mounted up and bolted in the rear position. Drive shaft is a bit further into the trans then I want....but then again I haven't got the rear end exactly where it needs to be. oh....and I came across this diagram of a 200-4r the other day. current drive shaft position: __________________ Kurt - '68 GMC short step - NIB '09 LY6 6.0L crate motor w/mods, NIB '12 crate 4L85e w/billet 3k stall Circle D, 3.73 posi 12 bolt, DynaTech f-swap headers, 3/4 drop, handling mods, etc. - my toy '72 Chevy LWB C-10 Highlander - 350/350 ps/pb/tilt/ac - not original but close '06 Chevy TrailBlazerSS - LS2/4L70e - little black hot rod SUV - my DD '18 Kia Sorento - wife's econo-driver '95 Chevy S10 - reg cab shortbed, LS, 4.3, auto... my '68's powertrain and chassis build -links broken A surprise phase - carb to efi -links broken

09-24-2010, 06:13 PM	#28
Mondo Registered User Join Date: Aug 2007 Location: Bakersfield, Ca Posts: 538	Re: 200R4 Swap ? I've had one in my 67 for a couple years now. The only issue I have is that it won't kick down out of lock up until there's a lot of throttle (or tap the brakes but it goes right back into 4th). It's a pain when in 30-45mph traffic as it lugs the motor. I've been to 3 tranny shops for adjustments but it hasn't worked out. My solution was to put in a small dash toggle switch connected to the brake switch sensor and switch off the lock out when cruising around town (back to basically a turbo 350). Do you guys have any problem with it releasing 4th gear lock up at a reasonable throttle position? Maybe I should continue my search for a tranny swap expert. Last edited by Mondo; 09-24-2010 at 06:15 PM.

09-24-2010, 06:33 PM	#29
ebfabman Registered User Join Date: Nov 2001 Location: Concord, NC Posts: 2,488	Re: 200R4 Swap ? I only use the lockup over 60mph.

12-17-2013, 06:59 PM	#32
C10_ustacould A day late and $1 short... Join Date: Dec 2008 Location: Northwest FL Posts: 3,877	Re: 200R4 Swap ? I would also like more info on installing a 200-4r behind a 250 I6, has anyone done more research since 2010? __________________ Buck Instagram: C10_ustacould 1963 SWB Fleet Side 528 Desert Beige Milly 1967 SWB Step Side 506 Medium Blue The Old Girl 1968 SWB Fleet Side 503 Light Green Ellie SOLD 1965 SWB Fleet Side 507 Light Blue Prescription Strength SOLD 1971 SWB Fleet Side 521 White Shiro SOLD 1968 SWB Step Side 503 Light Green My Old Farm Truck SOLD



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.