Is there a correct propeller shaft alignment? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

da-burb · 06-13-2003, 12:09 AM

I would assume that there is a right and wrong alignment on the front drive shaft. Looking at the constant velocity U-joint, if the front yoke on the drive shaft is horizontal, I am thinking that the other end at the slip shaft should be horizontal also. I looked under my other 4x4's and 2 were 90 degrees off and one was as I described. What say the experienced 4x4 gurus. (or doesn't it matter at all)

Blazer1970 · 06-13-2003, 07:56 AM

On a shaft with a double cardan joint at the t-case, it does not matter what the orientation of the other end (u-joint at axle) is.

**JIMs70GMC** · 06-13-2003, 08:18 AM

What Tim said. Also the angle at the u-joint end should be as close as possible to zero degrees.

da-burb · 06-13-2003, 08:23 AM

Thanks!

da-burb · 06-14-2003, 12:53 AM

Ok, now inside this double cardon joint is a spring. What is it's purpose? Because it sure doesn't look like it does much of anything.........

06-13-2003, 12:09 AM	#1
da-burb "Ochre Ogre" Join Date: Apr 2000 Location: Springfield, MN Posts: 3,558	Is there a correct propeller shaft alignment? I would assume that there is a right and wrong alignment on the front drive shaft. Looking at the constant velocity U-joint, if the front yoke on the drive shaft is horizontal, I am thinking that the other end at the slip shaft should be horizontal also. I looked under my other 4x4's and 2 were 90 degrees off and one was as I described. What say the experienced 4x4 gurus. (or doesn't it matter at all) __________________ Bowtie Truck Stop Inc. Mid-West GM Truck Restoration Parts Supplier Your Key Parts, Auto Metal Direct, Dynacorn, and Goodmark dealer. like us @ www.facebook.com/BowtieTruckStop 1971 C-10 Suburban (Ochre) 1971 K-10 Suburban (Ochre) 1972 C-10 Suburban (Ochre) 1972 K-20 Suburban (Yellow- that just aint right!) Springfield, Minnesota 56087

06-13-2003, 07:56 AM	#2
Blazer1970 Registered User Join Date: Dec 1999 Location: Old Mission, MI, USA Posts: 2,507	On a shaft with a double cardan joint at the t-case, it does not matter what the orientation of the other end (u-joint at axle) is. __________________ Tim

06-13-2003, 08:18 AM	#3
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	What Tim said. Also the angle at the u-joint end should be as close as possible to zero degrees. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

06-13-2003, 08:23 AM	#4
da-burb "Ochre Ogre" Join Date: Apr 2000 Location: Springfield, MN Posts: 3,558	Thanks! __________________ Bowtie Truck Stop Inc. Mid-West GM Truck Restoration Parts Supplier Your Key Parts, Auto Metal Direct, Dynacorn, and Goodmark dealer. like us @ www.facebook.com/BowtieTruckStop 1971 C-10 Suburban (Ochre) 1971 K-10 Suburban (Ochre) 1972 C-10 Suburban (Ochre) 1972 K-20 Suburban (Yellow- that just aint right!) Springfield, Minnesota 56087

06-14-2003, 12:53 AM	#5
da-burb "Ochre Ogre" Join Date: Apr 2000 Location: Springfield, MN Posts: 3,558	Ok, now inside this double cardon joint is a spring. What is it's purpose? Because it sure doesn't look like it does much of anything.........



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.