What did you do to your truck today!

[OG2wdblaze]

drove it...for the first time in about eight years I took it for a drive!!! also did a little body work and started smoothing my top!

[treeboy97]

I removed my saginaw 4 speed and tried in install a T5. I ran into a small problem with the clutch disk, I had bought an 11 and actually need a 10 inch clutch disk. I will start over next Saturday!

[alwaysbroken]

put the motor, trans, and tcase in my 4x4

[Navy Mechanic]

Finished installing front drop springs, spindles, shocks, ball joints, tie rods, etc.

[glider_6969]

I pulled the seats out,, again, and put in the speaker and storage box I made and then put the seat back in,,, i probably should have wiped it down before I took the pics,

[jhwkns]

Originally Posted by og2wdblaze

drove it...for the first time in about eight years i took it for a drive!!! Also did a little body work and started smoothing my top!

wtg!

[Bull72]

got a new alternator today =) I really wanted a chrome one, but that will have to wait.

[60ratrod]

Originally Posted by Bull72

got a new alternator today =) I really wanted a chrome one, but that will have to wait.

i hear that the chrome ones have less of a life span since the chrome keeps the heat in more than the natural cast ones

[Mike Bradbury]

Polished some chrome and did a compression test on the engine. All came out at 149 almost exactly. But I am still blowing a little smoke out the passenger side pipe when I romp on it.

[Bull72]

Originally Posted by 60ratrod

i hear that the chrome ones have less of a life span since the chrome keeps the heat in more than the natural cast ones

Well I am glad to hear that then =)

[Sonicman]

Put in headlight relays. I can't wait til it's dark to see the fruit of my labor!

[FlounderGDI]

I got the itch to work on the truck today so I braved the cold and bolted down my new bed mounted tool box... I also did some repair to my heater switch plug... Next up on the to-do list is to install my Skip White HEI...

[project 67 sub]

did a little more work on the replacement dash, wire wheeled the paint off, and cut out the radio hole. i offset the hole to the right because i am going to add a push button starter on the left side of it. i also might add a few other things as well but not sure yet, and i would have to figure out what exactly that would be first lol.

[project 67 sub]

not much of an update as of yet, but, just some messing around. took a pic of the current engine setup as i dont have a pic of that in here. i also pulled the springs out of the front to see how low it is. still need to finish the lower arms, and install bags and spindles, but i only have 3/4" before the arms hit the grond

[j_cst_10]

I bumped into it with my 2002 Silverado while pulling into the driveway.

[cobrajet21]

have not touched it in a year.

[project 67 sub]

ouch! did it do any damage???

[67Slider]

Replaced inner and outer tie rod ends, upper and lower ball joints, and cut one coil out of the front springs. Tried my wipers and found that I had installed the linkage backwards. Had to take the cowl off and swap the pivot arm. Buttoned her back up and parked her in the garage. I had replaced my rear springs with Jeep TJ springs awhile back. I finally got around to measuring the drop and come to find out one side is 1.75 inches higher than the other. I guess I will fork out the 100 bucks for real drop springs. I should have known better but it sounded like a great deal(the TJ springs).

[j_cst_10]

No, not that I can tell. I really don't know how it didn't mess something up. It does have 4 inches of snow on it so who knows.

[kpeztruck]

Originally Posted by magwakeenercew2jh

Yup. Kimber .45 CDP Ultra II.

Sold it yesterday.

Lookin' for wheels:

http://tinyurl.com/4qxg2tj

Must be a nice set of wheels you are hunting for, I still have my Kimber Compact 12 years later. Carry it everyday. Hate to see you have to part with such a nice handgun. Paul Baxter

[trkfrk]

Pulled engine/trans (mock-up) Prepped for powder coating. Cut 4" exhaust holes in frame. Sandblasted A-arms.

[bc gman]

I put the first coat of teak oil/thinner on the red oak bedwood,just the start of many coats.

[magwakeenercew2jh]

Originally Posted by kpeztruck

Must be a nice set of wheels you are hunting for, I still have my Kimber Compact 12 years later. Carry it everyday. Hate to see you have to part with such a nice handgun.

Thanks, Paul. I'm still covered. But that one was the most expensive I had. It took all of what I got for it for the Boss 338 20's. The "Little Woman" bought me tires for an early Valentine.

[dixietruck71]

picked up a 69 gmc grille last nite in killer shape, no rust. buffed and polished it tonight. gona put it on this weekend, along with all of the side trim finally.

[mcmlxix]

Put some red LEDs in the dash... I had already pulled it all apart and painted the inside a bright gloss white... they look good...