Console done...almost - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chevykid1969 · 06-29-2003, 03:45 PM

Here is a picture of my console and new seats. I am almost done just have to put new sub and amp in the console.Once i find them. (Thanks Riveted1 for helping me).

**Chevy4Life** · 06-29-2003, 04:27 PM

nice work. What is that covered with?

chevykid1969 · 06-29-2003, 04:29 PM

I coverd the sides with carpet and did the top in vinyl

69 Short Fleet · 06-30-2003, 03:14 AM

Great job Chevykidd!!!

MidniteChevy68 · 07-01-2003, 04:57 AM

Looking good!!!

JayDubBlazer · 07-01-2003, 06:12 AM

Good Place to mount speakers

ginter · 07-01-2003, 09:37 AM

Looks pretty good! How is the sound from that speaker placement? And more importantly, can you get a pic of the top of the console? I'd like to see it from that view.

**FRENCHBLUE72** · 07-01-2003, 07:56 PM

Nice counsol got anymore pic's and fab material's list???

MandarinSixSeven · 07-01-2003, 08:06 PM

ya I too want to know the materials and dimensions...I've been wanting to make one like that for a while now but didnt know if it would look good...but yours does, so you have inspired me

chevykid1969 · 07-01-2003, 08:16 PM

Ok Here is what i used:
3/4" plywood.
About 3 feet of 2x4's for bracing
Sides are covered in carpet
Top is covered vinyl.
For cup holders i went to Wal-Mart and found mesh pencil holders( there great they can even hold the really big drinks from Mc donalds)
The Holder thing on the back i picked up at Wal-Mart for about 2 bucks
Overall problaly cost me about 30 bucks.
The Dimensions
I used card boear to mock it up( worked great for the angle going toward the front.)
It is about 40" long
11" wide Outside
Inside it is 9 1/2 " wide
And it is 8" tall
For the gap from back of the console to the back of the truck i made a little panel so i can access my amp
Anything i missed

chevykid1969 · 07-01-2003, 08:18 PM

Top view
Not a very good picture

chevykid1969 · 07-01-2003, 08:22 PM

Here is a access panel i made so i can get to my amp
I covered it in vinyl too

06-29-2003, 03:45 PM	#1
chevykid1969 Registered User Join Date: Apr 2003 Location: Knightdale,North Carolina Posts: 377	Console done...almost Here is a picture of my console and new seats. I am almost done just have to put new sub and amp in the console.Once i find them. (Thanks Riveted1 for helping me). Attached Images

07-01-2003, 04:57 AM	#5
MidniteChevy68 Registered User Join Date: Feb 2003 Location: Sacramento, CA Posts: 53	Looking good!!! __________________ 68' Chevy truck longbed: flows, 4/6 drop, k&n filter, GMC front clip, and 20s

07-01-2003, 06:12 AM	#6
JayDubBlazer go cyclones Join Date: Jun 2003 Location: Ames, IA Posts: 1,885	Good Place to mount speakers __________________ Wes PROJECT OLE GREEN 1972 Blazer 4X4 350/700R4 2017 Silverado LT

07-01-2003, 09:37 AM	#7
ginter Registered User Join Date: Mar 2003 Location: Denver CO. Posts: 156	Looks pretty good! How is the sound from that speaker placement? And more importantly, can you get a pic of the top of the console? I'd like to see it from that view. __________________ Mike 67 C20 Camper Special - Rust Free! 1970 Porsche 914/6

07-01-2003, 07:56 PM	#8
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,604	Nice counsol got anymore pic's and fab material's list??? __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

06-29-2003, 04:27 PM	#2
Chevy4Life Senior Member Join Date: Feb 2003 Location: Las Vegas, NV Posts: 750	nice work. What is that covered with?

06-29-2003, 04:29 PM	#3
chevykid1969 Registered User Join Date: Apr 2003 Location: Knightdale,North Carolina Posts: 377	I coverd the sides with carpet and did the top in vinyl

06-30-2003, 03:14 AM	#4
69 Short Fleet Registered User Join Date: Nov 2002 Location: Kelowna B.C. Canada Posts: 1,086	Great job Chevykidd!!!

07-01-2003, 08:06 PM	#9
MandarinSixSeven Seasonal Poster Join Date: Apr 2002 Location: Kelowna BC Canada Posts: 896	ya I too want to know the materials and dimensions...I've been wanting to make one like that for a while now but didnt know if it would look good...but yours does, so you have inspired me __________________ 67 GMC Short Step 350/4-Speed/3.08 Posi Front/Rear Sway Bars Kelowna BC, Canada Member of DTPW

07-01-2003, 08:16 PM	#10
chevykid1969 Registered User Join Date: Apr 2003 Location: Knightdale,North Carolina Posts: 377	Ok Here is what i used: 3/4" plywood. About 3 feet of 2x4's for bracing Sides are covered in carpet Top is covered vinyl. For cup holders i went to Wal-Mart and found mesh pencil holders( there great they can even hold the really big drinks from Mc donalds) The Holder thing on the back i picked up at Wal-Mart for about 2 bucks Overall problaly cost me about 30 bucks. The Dimensions I used card boear to mock it up( worked great for the angle going toward the front.) It is about 40" long 11" wide Outside Inside it is 9 1/2 " wide And it is 8" tall For the gap from back of the console to the back of the truck i made a little panel so i can access my amp Anything i missed

07-01-2003, 08:18 PM	#11
chevykid1969 Registered User Join Date: Apr 2003 Location: Knightdale,North Carolina Posts: 377	top view Top view Not a very good picture Attached Images Last edited by chevykid1969; 07-01-2003 at 08:25 PM.

07-01-2003, 08:22 PM	#12
chevykid1969 Registered User Join Date: Apr 2003 Location: Knightdale,North Carolina Posts: 377	Access panel Here is a access panel i made so i can get to my amp I covered it in vinyl too Attached Images



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.