The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-12-2011, 02:17 PM   #1
bean
Registered User
 
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
pinion seal and bearing

the diff on my 72 is leaking from the pinion seal so i know i'm going to need to atleast replace that. question is how do i tell if the actual pinion bearing is bad? I'm wondering if i shouldn't just rebuild the differential. any thoughts?
bean is offline   Reply With Quote
Old 03-12-2011, 02:34 PM   #2
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,708
Re: pinion seal and bearing

You usually get noise if the bearing is bad but a guy may not always hear that running down the road.

It isn't hard to replace the pinion seal though, but for most of us rebuilding the rear end is a job that you call in the professionals for. I'll do almost everything on my trucks myself including engine, trans, body and paint but won't touch a rear end that doesn't have a drop out center section.

Last edited by mr48chev; 03-12-2011 at 02:36 PM.
mr48chev is offline   Reply With Quote
Old 03-12-2011, 02:40 PM   #3
bean
Registered User
 
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
Re: pinion seal and bearing

thanks that's probably good advice. my idea of rebuilding would simply be replacing pinoin bearing and wheel bearing. no i don't hear any noise going down the road. a guy i work with said when you take that flange off you'll be able to tell if the bearing has worn into it some and if so then it needs to be replace. is this true?

i'd much rather just replace the seal at 7$ lol
bean is offline   Reply With Quote
Old 03-12-2011, 02:46 PM   #4
Hottrucks
Redefining LowBudget
 
Hottrucks's Avatar
 
Join Date: Mar 2009
Location: lebanon Cow Hampshire
Posts: 4,538
Re: pinion seal and bearing

Quote:
Originally Posted by mr48chev View Post
You usually get noise if the bearing is bad but a guy may not always hear that running down the road.

It isn't hard to replace the pinion seal though, but for most of us rebuilding the rear end is a job that you call in the professionals for. I'll do almost everything on my trucks myself including engine, trans, body and paint but won't touch a rear end that doesn't have a drop out center section.
LMAO ^^^^ thats so me too!!


I would also check the vent the mud wasps like them and if it gets hot inside then it will want to push oil out in odd places
__________________
1970 C10 CST fleetside 472 ....big dreams little cash...
SunShine Syndicate..

Mikes Sandwich Fair Run OCT 8th 2011
Hottrucks is offline   Reply With Quote
Old 03-12-2011, 02:50 PM   #5
1970 Bowtie
It's all in the timing
 
1970 Bowtie's Avatar
 
Join Date: May 2009
Location: Lake Mary,Florida
Posts: 600
Re: pinion seal and bearing

Quote:
Originally Posted by Hottrucks View Post
LMAO ^^^^ thats so me too!!


I would also check the vent the mud wasps like them and if it gets hot inside then it will want to push oil out in odd places
X3,yall have dirt dobbers that far north.
__________________
The Dude Abides.
----------------------
I aint sayin, I'm just sayin.
1970 Bowtie is offline   Reply With Quote
Old 03-12-2011, 04:13 PM   #6
Hottrucks
Redefining LowBudget
 
Hottrucks's Avatar
 
Join Date: Mar 2009
Location: lebanon Cow Hampshire
Posts: 4,538
Re: pinion seal and bearing

Quote:
Originally Posted by 1970 Bowtie View Post
X3,yall have dirt dobbers that far north.
yep....they find the funny places to get in to?
Hottrucks is offline   Reply With Quote
Old 03-12-2011, 05:20 PM   #7
Wrenchbender Ret
Registered User
 
Join Date: Oct 2005
Location: Overland Park, Ks.
Posts: 5,229
Re: pinion seal and bearing

If its not making noises your brgs are probably OK. When you pull the old seal you can remove the frontr brg & examine it. You can pull the rear cover & make sure there is no side to side movement in the carrier brgs. or unusual pieces in the bottom of the houseing. Mark the pinion nut & the shaft before you take it off so you can put it back in the same place. Clean it off & put some locktight on it as the self locking is probably worn out. Put in a new seal & fresh grease & you are good to go. If the pinion flange has a groove in it were the seal rides you can get a speedy sleeve to go over it.
Wrenchbender Ret is offline   Reply With Quote
Old 03-12-2011, 08:14 PM   #8
JimKshortstep4x4
Senior Member
 
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
Re: pinion seal and bearing

When pinion bearings go bad they will make a lot of noise when you let off of the gas. I really doubt if you have bad bearings if you have not heard anything. As mentioned make sure the vent is good and just replace the seal. If the lube looks bad then changing out the gear oil would be recommended.

Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end
1965 Impala SS 400 sbc, Muncie rock crusher
1966 Impala SS 396 bbc, TH 400
1969 El Camino, 350 sbc, TH 350
1971 Snowplow built on a Blazer frame
1972 GMC Short bed, stepside, TH 400, 427 BBC
JimKshortstep4x4 is offline   Reply With Quote
Old 03-13-2011, 12:51 AM   #9
jerry moss
Born Psycho
 
jerry moss's Avatar
 
Join Date: Feb 2001
Location: brentwood,cal,usa
Posts: 4,936
Smile Re: pinion seal and bearing

trust me, rebuilding rear diff's isn't all that difficult. i used to be scared to death of them but when we got a diff guru at our shop and he taught me the proper way to diagnose, clean and build, it's really not difficult- time consuming sometimes but not difficult- with the proper tools. i have only done semi floaters, chevys, dodges, jeeps and fords so far but one of these days i plan to tackle one of my 14 bolt full floaters.
__________________
jerry moss
72 cheyenne super K20- tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,tow hooks,bumper guards,toolbox,aux. fuel tank,posi front and rear,plus other goodies!!! SOLD
69 suburban K20-tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,4 inch all spring lift,4 speed, 14 bolt full floater, dana 44 HD,warn winch,posi front and rear,tow hooks,plus other goodies.
73/80 chevy/gmc K20 SB400,turbo 400,205,tilt,a-c,gas hog.
77 K/5 cheyenne blazer-daily driver/beater. SON HAS IT NOW
BRENTWOOD,CALIFORNIA
jerry moss is online now   Reply With Quote
Old 03-13-2011, 05:47 PM   #10
bean
Registered User
 
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
Re: pinion seal and bearing

thanks for the responses. it turned out there was alot of caked up mud around the vent i cleared away. hopefully that will take care of it if not i feel good about just replacing the seal. thanks again
bean is offline   Reply With Quote
Old 03-13-2011, 06:26 PM   #11
fastwillie 696969
~Rest In Peace~
 
fastwillie 696969's Avatar
 
Join Date: May 2005
Location: CALIFORNIA NOR CAL
Posts: 9,707
Re: pinion seal and bearing

proper way to get measure the backlash on the ring and inspect the gears itself,there is a crush sleeve, i would replace that since your replacing the seal too ,but if you rebuild it complete its not that hard some people get intimanded by the shims ,or clutch pac if posi ,if its a one legger (open diff. )my sister can rebuild one of those.
__________________
is it fast ? it has a lighting bolt donut?


B___H please, I can remove 90% of your so called "beauty" with a kleenex
fastwillie 696969 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:39 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com