|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
06-28-2011, 09:02 PM
|
#1 |
|
Registered User
 
Join Date: Feb 2009
Location: Redding, Ca
Posts: 333
|
How much to shorten drive shaft?
What should I pay to shorten drive shaft (in california)? My last one on my 65 was $250. Was a 2 piece shaft, u-joint in middle and one on each end. Used old u-joints, I supplied new yoke. Seemed pretty high, maybe I am out of touch?
|
|
|
|
06-28-2011, 09:56 PM
|
#2 |
|
Registered User
Join Date: Mar 2011
Location: Spring, Tx
Posts: 365
|
Re: How much to shorten drive shaft?
I would think about 75 to 125 bucks. I know i can get one made for about 250.
__________________
1968 C10 SWB Dropped 5 in tha back 3 in tha front My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=470902 |
|
|
|
|
06-28-2011, 10:04 PM
|
#3 | |
|
Registered User
Join Date: Feb 2009
Location: Redding, Ca
Posts: 333
|
Re: How much to shorten drive shaft?
Quote:
|
|
|
|
|
|
06-28-2011, 10:59 PM
|
#4 |
|
Registered User
Join Date: Apr 2000
Location: Bonne Terre, Mo
Posts: 3,005
|
Re: How much to shorten drive shaft?
And you didn't get new joints for $250. For $50 more they should have nickle plated a dash plaque and give you a kiss too. Sounds a little extreme. On ebay in the past years there was a guy in Ca. custom making shafts and shipping them for $175-$225 balanced but they were one piece shafts but he supplied new yolk and all for that price. That may not be out of line price wise though. A few members on the board do that kinda work. Let them chime in on the cost.
__________________
'69 Chevy Long Fleet & '71 GMC Short Step & Project "ODD BALL" "You can wash a pig, soak it in most expensive perfume. In the end it is still just a pig." ODD BALL build thread http://67-72chevytrucks.com/vboard/s...d.php?t=478629" |
|
|
|
|
06-29-2011, 05:50 AM
|
#5 |
|
Registered User
Join Date: Aug 2010
Location: Alta Loma, CA
Posts: 610
|
Re: How much to shorten drive shaft?
I paid $230 at Inland Driveline in Ontario, CA, but that was a 1 piece with all new U-joints and a new slip yolk.
__________________
67 5.3L Build |
|
|
|
|
06-29-2011, 06:21 AM
|
#6 |
|
1969 Custom 30 wrecker
Join Date: Sep 2001
Location: Pottsville, Pa
Posts: 2,611
|
Re: How much to shorten drive shaft?
I had a machine shop cut 3" out of one for my stepside about 10 years ago for a whopping $30 dollars.
__________________
Bob 63 Impala 283/PG/3.36 (under restoration) 66 Impala 327/PG/3.36 66 Chevelle SS 409/M22/3.55 69 Chevelle 307/PG/3.08 (future restoration) 69 C10 short stepside 454/TH350/3.73 69 Custom 30 tow truck 350/4 spd/4.10 (resto done, CRUISIN TIME!) 71 Cheyenne 20 fleetside 350/4 spd/4.10 71 Chevelle 6/PG/3.08 72 Chevelle 454/M21/4.10 |
|
|
|
|
06-29-2011, 09:38 AM
|
#7 | |
|
Registered User
Join Date: Feb 2011
Location: OLIVEHURST CA
Posts: 570
|
Re: How much to shorten drive shaft?
Quote:
|
|
|
|
|
|
06-29-2011, 11:16 AM
|
#8 |
|
the boat guy
Join Date: Jul 2007
Location: springfield mo
Posts: 2,339
|
Re: How much to shorten drive shaft?
65 for a 1 piece or 95 for a 2 piece is what we charge for a shorten and BALLANCE! No ujoints, no carrier bearing, no yokes, if it is a 2 piece we will check the center stub, bolt on yoke, and carrier bearing. I don't know what our 2 shops in california charge but I cant imagine much of a difference.
theirs no way I'd ever install a driveshaft that wasn't properly ballanced. You can if you wish, it does make it cheaper in the short run. If you don't ballance both pieces of a 2 piece driveline together as an assembly they are not ballanced.
__________________
67, swb, fleet, tach, throttle, 5.3, 4l60e, 3.73's, fuel cell, 5 lug, p.d.b., 4-6 drop. great little truck 66, stevens drag/ski 18' silouette, 350, 2.02 doublehump heads. comp extreme marine 278 cam, vette 7 fin valve covers, old polished edelbrock intake, velvetdrive, casale v-drive, adj cavitation plate. 28, model a rpu project, |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
