![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Jun 2011
Location: Atlanta ga
Posts: 150
|
Replaced Gas tank today
I replaced my driver's side gas tank today in my 1984 C20.
I installed the tank from the underside of the truck. Everything was going great until I got to the point of reattaching the fuel lines and electrical wires (for the fuel sender). The red wire would not snap on the fuel sender. I had the 20 gallon tank laying across my chest, and it was a bear to attach the fuel lines. I will be revisiting all of this when I pull the bed later this summer for body work. Next time, I will be pulling the bed. I wrestled with installing the new tank for at least 2 hours (4 hours total including removing the old and cleaning the mounts). While I was under there, I notice that about 3" section of my frame has a slight bend (flares downward about 1/4" to 1/2") just on the lower lip of the c-channel. The top section appears fine. I have attached a pic of an example of where the bend is located. Is this something that I could just hammer back into place? Are our frames heat treated? |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Apr 2010
Location: Newcastle, OK
Posts: 1,344
|
Re: Replaced Gas tank today
That is there purposely from the factory to make room for the catalytic converter.
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jun 2011
Location: Atlanta ga
Posts: 150
|
Re: Replaced Gas tank today
Cool, I was wondering about that. It is only on the drivers side.
__________________
1984 C20, 454, 4 speed named "Gold Member" |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jun 2011
Location: Baytown TX
Posts: 2,219
|
Re: Replaced Gas tank today
My 82 is the same way, the first time I crawled under my truck and saw it I was pissed.
__________________
John 82 Chevy Silverado 350ci/TH350 ![]() |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Feb 2007
Location: Austin, TX
Posts: 3,930
|
Re: Replaced Gas tank today
When I had my tanks out, I removed them from the bottom with the bed on. I disconnected the hoses at the hard lines on the frame. For the new hoses, I attached new sections of hose to the sending unit. I threw the new hose over the frame then raised the tank into place, and hooked the hose to the hard line afterwards.
For lowering and raising the tank, I used a long piece of wood and a floor jack to help out.
__________________
1977 GMC Sierra Grande |
![]() |
![]() |
![]() |
#6 |
Robert Olson Transport
![]() Join Date: Oct 2002
Location: recent transplant to NC USA
Posts: 20,288
|
Re: Replaced Gas tank today
this is the way to do this
__________________
Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!! |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: May 2010
Location: laurel hill Fl
Posts: 645
|
Re: Replaced Gas tank today
also a good tree and a hoist make lifting the bed of much easier. its always easier to work from the top.
__________________
1985 C10 Custom Deluxe LWB 305/700r4 [ Goldfinger ] ![]() 1999 k3500 crew cab dually 6.5tdi/4l80e |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: May 2011
Location: Bradford, PA
Posts: 395
|
Re: Replaced Gas tank today
When I did my gas tank, I left the bed on, and had to do everything with no help or support... A simple job ended up turning into a 8 1/2 hour day...lol
__________________
1981
![]() 305 ci | TH350 | NP208 | 60k miles |
![]() |
![]() |
![]() |
Bookmarks |
|
|